Wilson Witt series 1 speakers, very odd problem, help!


Ok so I have a pair of Wilson Witt series 1 speakers I purchased used approx. 4 months ago and was very happy with them.
Now I am experiencing a very odd problem.
Roughly 50% of the time when I start playing music through them the mid drivers do not work at all on either of them.
This usually occurs if I am playing at night and START at lower volume levels.
The next day I play them maybe at much higher start volume they will work just fine.
That is what is most peculiar to me, just how they can work one day but not the next and work again.
I am not sure it is directly related to volume but that does seem to be when they decide to not work.
Does anybody have an experience with this or have any ideas what possibly to look for?
Source does not matter, it could be tt or cd or tidal, and usually when the mid drivers are not working just turning up the volume does not make them work on that run.
Very very odd and I truly cannot fathom just how this can be happening at all?
128x128uberwaltz
Fitted the new Focal 121t tweeters last night and now we have sweet music again, better that the originals? Hard to tell as been a while since have listened to the speakers with all drivers fully functional...lol
Crazy part though....the cheapest place to buy these tweeters from even after shipping was W.A.R Audio in Perth, Australia!
Oh well, Im now happy.....
Purchased a pair of updated brand new Focal t120 tweeters and waiting for them to arrive and hope that will be the end of my woes.
3 to 10 business days...groan...lol
I replaced resistors for mids and tweeters at same time.
The tweeter on one speaker is def bad, it sounds awful but needed to do all resistors first.
I found a pair from Wilson Sofia 1 on eBay and also some focals but looking for info first
Thank you
Replace the resistors for the tweeters too. If that doesn’t work, make sure the tweeters you buy are voiced for the speakers. There were a lot of several of them on here recently, but there is no guarantee they are voiced for yours.My series II are very well built, and have 4 steel bolts and plates on the bottom of them. Best of luck and let us know if it was just the resistors in the tweeters.
Well finally got time to replace the resistors this morning, little surprised to see that for all the money Wilson charge they use plasterboard screws to hold it together with the square heads!
Anyhoo we now have life at the mids but the tweeters are definitely shot, most likely from my daughter using them when the mids were not working at all.
So any recommendations for a good replacement tweeter for these?  
MAKE SURE TO PUT TAPE IN ANY SLOTS TO CATCH ANY DROPS OF SOLDER FROM POSSIBLY HITTING SOMETHING YOU DON'T WANT, THEN REMOVE THE TAPE.
Just and update so far
I pulled one mid driver to test solo and lo and behold music so I am going to assume both mids are good.
Spoke with Jerron at Wilson who confirmed that the likely cause is the resistor on the crossover and that they are accessed by a panel on base of the speaker.
I ordered 4 resistors for both mids and tweeters( may as well do both while at it) and just waiting for them to arrive and hopefully that will be it.
i'm not sure if this is relevant but i had driver doing similar things and eventually if failed completely it turned out to be the voice coil wire was broken just were it entered the coil. one of the things i noticed was when the speakers were playing if I lightly pressed in the cone it would make contact and play.... good luck with your issue
@KALALI    
Along the same lines as audioconnections thought process I think and a fairly quick and cheap test for sure!
Thank you!   
Last time I had a similar problem with my loudspeakers, of course nowhere near the caliber of yours, I tested the driver - one woofer, by removing it from the cabinet and hooking it up to my cheapo integrated amplifier at the time. It turned out to be a bad connection and a simple fix. YMMV.
And I meant I was now going to call Wilson just to see how I get into to check resistors on the crossover without damaging the finish anywhere
So yes there is a lot of point to my post to see how others may have fared with the same speakers or good thoughts as per audioconnections last suggestion
@audioconnection 
not quite sure what you mean by play it solo out of the cabinet?
do you mean desolder it from the main wiring and just hook up a pair of speaker leads to it and play direct at very low volume from my amp?
if so not a bad idea at all, thank you!
@gdnrbobThank you for your concern. How do you know I have not already spoken at length to polk432?
Which I have at length......
I questioned audioconnection simply because I did not see how pics would go is all.
What are your suggestions?
Pull the driver first and play it solo out of the cabinet
if it sounds dead or distorted with piano music there you go
You have 2 offers for help, yet you question Johnny's (Audioconnection) rationale, and then say you will contact Wilson. 
Why bother posting?
B
@audioconnection 
what are you thinking on the binding posts? they are not overtightened etc?
the mid woofers themselves externally look like new, internally when I removed them to check for loose connections there was some very minor dust and light corrosion on the frame but that was it.
soldered connections were good.
I am leaning towards blown resistors on the crossover but have yet to figure out how to even get to them to check.
It looks like the side panels should come off but when I prised off the caps that I would have though covered a screw or bolt head all I saw was what looks like factory applied blob of adhesive?
will be calling Wilson tomorrow to try and get good info to proceed further.
Should be simple enough to replace the resistors if it is them but do not want to risk any damage to the speakers or finish monkying around trying to get into the them the WRONG WAY.
Take a picture and share it here of your speakers binding posts
 and Pics of mid woofers
An update to this as I played them this morning at higher volume, after being on vacation for a week.
Now the mids will not play at all and it sounds like the lh speaker tweeter is also on the fritz as just sibilance is all I can here.
maybe something on the crossover boards?
Any thoughts will help here, thank you