Streaming Sound Quality - Want the very best sound quality? Network Acoustics ENO...


Like many of you fellow Agoners I am striving to get the best sound quality out of my digital streaming front end. To that end I have invested in various high end switches, re-clockers, ethernet cables, various USB filters/re-clockers, high end servers and delved into fiber optic conversion configurations. All of these measures did improve sound quality at varying levels. I felt my system sounded as good as a decent CD transport on many streaming recordings in Qobuz. However, I still felt there was something missing. I felt my system was still being held back. You can see my system under virtual systems here.

Well, I stumbled across something that has finally enabled my digital system to be all it can be. I cannot fully express the level of sound quality improvement realized with the addition of the Network Acoustics ENO Ag filter and ENO Ag streaming ethernet cable. It has been 10 days now since I added these to my system and I can now confidently say my streaming and system are all they can be sonically.

Here is the set up that has caused me to sell off and move past many other powered filters, reclockers, fiber optic options, and other streaming tweaks and gadgets. Frankly, the ENO additions are miles ahead of these other options sonically in my system and experience. Miles. This is my personal experience and please understand this perspective.

Netgear NighHawk modem/router power by an LPS > Supra cat 8 ethernet cable > English Electric 8Switch > Network Acoustics ENO Ag streaming cable > ENO Ag ethernet filter > Innuos Zenith III > Mojo Audio Evo dac

The English Electric 8Switch is also wonderful. Will a lower cost, standard switch sound as good in this set-up? Not sure as I have not tried. I am so ecstatic with my sound system that I don’t want to touch it!

There is a certain rightness from top to bottom that’s intoxicating. The tone is so beautiful and natural with no hint of electronic glare or digital artificiality. Music flows with far greater ease and has an uncanny, unforced nature to it. The stage is far deeper with the music flowing from a plane that is layered and completely separate of the speakers. This aural sensation, at this level of nuance, is new to my system and experience. The ENO products made this possible.

Instruments are presented with a new realism that is arresting to my senses. There is a wholistic presentation that spreads out all around me and my space. Just a joy to experience. Yes, the speakers seem to float the music into my space without any attention or localization of the speaker box or physical presence.

No part of frequency spectrum is out of place or forced. I am sure this has to do with the absence of noise. My music is equally articulate and resolved at low or loud volumes. Music stays controlled and enticing no matter how complex or bombastic the recording.

The ENO filter is passive, not powered, so there is no need of any power supply or plug. This is a huge plus.

Hope you streaming audiophiles find this helpful.

Bill
128x128grannyring

Thanks @lalitk for your reply.

Too bad that I cannot use ENO with Melco N1Z directly. I don't know putting it before the switch would be just as effective. Speaking of switch, doesn't Melco also sell a switch with 100mb/s ports just for audio applications? If that works with N1Z, then the ENO should also? Anyways, I ordered a RJ45 coupler so I can try using another short cable between ENO and the streaming device, see if that works...

@liangx5 

The Melco S100 switch has 4 ports rated at 100MbE speeds and 4 ports rated at 1GbE. As far ENO goes, I suggest that reach out to Rich at Network Acoustics about compatibility issues with N1Z. Hope you get this sorted out soon! 
 

The Muon filter is compatible as I understand and I would confirm with Rich. 

Thanks @lalitk, @yoby and @grannyring. I just sent an inquiry to Network Acoustics. Shall see what they have to say. I also read in another forum that adding a 100mps switch in front of ENO should help. Since the switch I have is a managed one, Buffalo BS-GS2008, maybe I can adjust speed for the connected port down to 100mps, hope that would work.