2. misc-audio
  3. 131672-481

The new Synergistic Research BLUE fuses ....

New SR BLUE fuse thread ...

I’ve replaced all 5 of the SR BLACK fuses in my system with the new SR BLUE fuses. Cold, out of the box, the BLUE fuses stomped the fully broken-in SR BLACKS in a big way. As good as the SR BLACK fuses were/are, especially in comparison with the SR RED fuses, SR has found another break-through in fuses.

1. Musicality ... The system is totally seamless at this point. Its as if there is no system in the room, only a wall to wall, front to back and floor to ceiling music presentation with true to life tonality from the various instruments.

2. Extension ... I’ve seemed to gain about an octave in low bass response. This has the effect of putting more meat on the bones of the instruments. Highs are very extended, breathing new life into my magic percussion recordings. Vibes, chimes, bells, and triangles positioned in the rear of the orchestra all have improved. I’ve experienced no roll-off of the highs what so ever with the new BLUE fuses. Just a more relaxed natural presentation.

3. Dynamics ... This is a huge improvement over the BLACK fuses. Piano and vibes fans ... this is fantastic.

I have a Japanese audiophile CD of Flamenco music ... the foot stomps on the stage, the hand clapping and the castanets are present like never before. Want to hear natural sounding castanets? Get the BLUE fuses.

4. Mid range ... Ha! Put on your favorite Ben Webster album ... and a pair of adult diapers. Play Chris Connor singing "All About Ronnie," its to die for.

Quick .... someone here HAS to buy this double album. Its a bargain at this price. Audiophile sound, excellent performance by the one and only Chris Connor. Yes, its mono ... but so what? Its so good you won’t miss the stereo effects. If you’re the lucky person who scores this album, please post your results here.

http://www.ebay.com/itm/ULTRASONIC-CLEAN-The-Finest-Of-CHRIS-CONNOR-Bethlehem-Jazz-1975-NM-UNPLAYED-...

Overall impressions:

Where the RED fuses took about 20 hours to sound their best, and the BLACK fuses took upwards of 200 hours of total break-in, the BLUE fuses sounded really good right out of the box ... and that’s without doing anything about proper directional positioning. Not that the BLUE fuses don’t need breaking in, they do. The improvement continues through week three. Its a gradual break-in thing where each listening session is better than the last.

Everything I described above continues to break new ground in my system as the fuses continue breaking in. Quite honestly, I find it difficult to tear myself away from the system in order to get things done. Its truly been transformed into a magical music machine. With the expenditure of $150.00 and a 30 day return policy there’s really nothing to lose. In my system, its like upgrading to a better pre amp, amp, CD player or phono stage. Highly recommended.

Kudos to Ted Denney and the entire staff at SR. Amazing stuff, guys. :-)

Frank

PS: If you try the SR BLUE fuses, please post your results here. Seems the naysayers, the Debbie Downers and Negative Nellie’s have hijacked the original RED fuse thread. A pox on their houses and their Pioneer receivers.

Frank



128x128oregonpapa
geoffkait's avatar
geoffkait
23,365 posts
 
jafreeman

geoffkait: “Not sure I go along with your detective work. Graphene would not enhance conductivity unless it were somehow incorporated into the fuse wire itself. Graphene on the fuse body could not (rpt not) enhance conductivity otherwise natural failure of the thin wire would not prevent disaster." Geoffkait

Not sure either--just that, the graphene is the breakthrough in the SR Blacks and Blues and is visible in the fuse body, so just what is it doing there if not enhancing conductivity? I propose it does enhance conductivity, but if the fuse element melts, the graphene by itself is unable to conduct the over-current. Any other ideas?

>>>>>Well, I don’t want to reveal the big secret in case SR wishes to keep it that way, but obviously what you see on the outside body of the Black Fuse and the Blue Fuse cannot be Graphene. So, the Graphene must be hidden. And the graphene is almost certainly not part of the wire. So it must be under the black or blue fuse wrapper, but not all the way across the fuse body because Graphene is highly conductive. Ooops! Did I just give it away?
nonoise's avatar
nonoise
10,569 posts
 
@geoffkait 

You took the cheese outta my trap. 🧀🐭
jafreeman's avatar
jafreeman
689 posts
 
Geoff---so, what is the material we are warned via package insert not to remove, as seen and touched on the SR Black and Blue fuse bodies? Is it to seal in the conductive material, placed after assembly? I still say the obvious: since the fuse element itself is such a poor conductor, there must be an enhanced conduction pathway to supplement the element, which can still interrupt an overcurrent by melting. I haven’t heard any better ideas around here, and that is what is needed now for this thread to evolve.
nonoise's avatar
nonoise
10,569 posts
 
I would think it due to it’s ability to quell vibrations. As a conductor, if bonded to metals (covetics) it would able to withstand 1500º C before melting, defeating the the fuse wire’s intended purpose.

Ceramics were a definite step up over glass and what SR uses is a step up from ceramics (if it is used over the ceramic tube). I could be wrong but I just did a quick read on covetics which eliminates the metal wire/graphene bonding question.

All the best,
Nonoise

georgehifi's avatar
georgehifi
10,312 posts
 
"The Awesome Foursome"  are at it again, waffling for the sake of boosting the thread. 

Waffel>https://forum.audiogon.com/posts/1548844

It beggars belief that sane person could think and have a discussion about this total "snake oil"

"The Awesome Foursome"
https://s3.amazonaws.com/lowres.cartoonstock.com/miscellaneous-leader-blind_leading_the_blind-lead_t...

Cheers George
More to discover