2. cables
  3. 155343-11545

Power cable with small connector / termination

I am planning to make a change to move equipment to a more accessible location on a built-in cabinet/bookshelf in my house. The electrical outlet is in the lower section behind closed cabinet doors, but I want to have equipment on top of that, in the open area of the bookcase. This requires me to drill a hole at the back of the bookcase through the top of the lower cabinet so I can pass the power cable through it. I'd like to use a quality cable but all of the ones I currently own have gigantic heads on them and I don't really want to drill a 3 inch hole through the cabinet. Does anyone know of any power cables that have slightly more reasonably sized terminations? At least at one end, as I only need to feed it through one way.
jnehma1
9 responses Add your response
mbolek
164 posts
 
Jon,

I have done this several times with my sideboard.  Pop off the IEC side (as many cables don't connect the shield at that end) remove the L, N, G wires, route the cable through a much smaller hole, re-terminate and now you have a very clean install.   Obviously, not ideal if you plan on changing out the cable periodically.  

Marty
jnehma1 OP
111 posts
 
@bryhifi That's a good idea, I will check tonight. Thanks!
bryhifi's avatar
bryhifi
373 posts
 
jnehma1,

Do the connectors have screws visible?  As in removable like most aftermarket connectors.  If so and you are comfortable with a minor task of removing and re-installing one end you can reduce your drill size to that of the cord diameter + 1/8".   Sending the un-terminated end up through the now much smaller hole and re-installing the connector from up top.  Guessing you would now be in the 3/4" to 1-1/8" range for the pass-through holes. 

Just a thought to work with what you already own and not have to spend more for the sake of connector size.


jnehma1 OP
111 posts
 
Thanks all for the tips. This is for a US 15-amp plug. An IEC isn't that big but all the cables I own have an IEC sticking out of a huge cylindrical head that's the same size as the male end of the plug. Maybe 3 inches is a stretch but definitely a 2 inch hole would be needed. I do see some of the Cardas cables seem to have smaller heads on them. Looks like Pangea cables also have small heads too. I have one of those somewhere I can measure to see for sure.
erik_squires
15,657 posts
 
Would you consider using high quality cables to make your own? That would solve your size issues.
erik_squires
15,657 posts
 
Sorry, not the AC cables, but the AC connectors.
erik_squires
15,657 posts
 
The Cardas AC cables are relatively small.  Check them  out.
bryhifi's avatar
bryhifi
373 posts
 
OP,
If you are handy putting a new IEC 320 end on, and either of these is smaller than your current connector, they would need a hole of about 1.75" to pass through.

http://www.furutech.com/2014/02/27/8612/

http://www.furutech.com/2014/04/22/9034/

I have several Furutech ends that are at or in excess of 1.5" diameter and needed 1.75" holes to pass through a custom built wall unit.
millercarbon's avatar
millercarbon
12,531 posts
 
3" diameter? Surely you exaggerate.

You don't say where you are, but if its an IEC connector those are only a little over 1". Probably a 1.25" hole will suffice. Or maybe you're trying to run several through just one hole and left out that little detail. Which happens a lot. Asking questions with sketchy partial inaccurate and/or irrelevant background information I mean. 

Still, buying power cables based on diameter, got to be worth points for originality. So, given that we know sound quality is no longer the main focus why not simply unscrew the connector from one end, slide the cable through, and re-attach the connector?


Log in to respond
More to discover
80x80
Revelation Audio Labs 'Paradise' CryoSilver Reference interconnect, WBT Nextgen
80x80
Nordost Odin 1
80x80
Silnote Audio Poseidon Signature
Silver/ 24k World's Finest Reference Cables Amazing Reviews