Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
Paul,

To me, if 2V plays loud enough then go with the lower of the two voltages. Why use a jackhammer to drive a nail. 2V was plenty for the RM-10, Auricle Music Blocs, and S-30, and the S-30 had nearly 3 times the sensitivity rating as the other two amps.

I was under the impression the output impedance did vary on the Lightspeed. If it doesn't, that is another significant benefit versus other passive designs.

George?
Correct me if I am wrong. I understand that in applying attenuation to the input signal, the Lightspeed or any passive converts the extra voltage to current and lowers the output impedance, both of which help to drive the amplifier effectively. That may be the reason why 3.9V is preferred over 2V - to achieve the extra headroom?
Maybe it is the input impedance of the LS that is constant? I've confused myself (again).
Wow busy while I was asleep.
Pubul57
Anthony, I'm not sure if you would know this, but if a CD player can be switched for output level (The EMM Labs can be switched between 2v and 3.9v)is there any theoretical reason why one should sound better or different, assuming 2v plays loud enough?Pubul57

You have to watch this one, if it changes the gain via the feedback network of the output stage opamp/amplifier then all will remain the same output impedance wise.
But if the highest output of 3'9v may have say have an output impedance of 100ohms then when you push the switch for 2v this could just introduce a simple voltage divider into the output circuit, which is a series & a shunt resistor this then will change the output impedance of the of the unit from the original 100ohms to whatever the series resisitor is of that voltage divider, it may 1000ohms.
Cheers George