RCM recommendations

Fastxr, What you are saying, about poor build quality of a VPI Model 17, is virtually akin to saying you bought a 1978 Chevy Camaro, and the engine knocked, leaked oil, had bald tires, and was in a poor state of repair.

This model 17 you acquired is most likely many years old, may have seen a number of different owners, cleaned 70,000+ records, and was a unit that went through much use, much misuse-neglect.

I'm not sure, but what you say about an open top to both resovoirs on the 17 having open tops to them, is still possibly true today, that the resovoirs are buttoned up to a bare sheets of MDF, thus exposed to the ravages of moisture, and time.

These can be addressed by an end user, but perhaps many would agree for the price that is paid, they shouldn't have to be.

Rubber Foam Gaskets, which are commonly used to seal Vacuum Motor to Resovoir tank will dry, rot, shrivel, and go bad over time. Nothing, especially parts like this last forever. It would be like saying "my oilpan gasket should've lasted forever on my $60,000 Mercedes", but eventually all things can wear out.

I've done a number of mods to my own VPI 16.5 RCM to enhance its performance, and increase its longevity for long term, heavy duty use.

They are not that hard to work on, and inspect, repair, and modify. I'll agree that MDF is not the ideal material to ever be used in the vicinity of fluids, so with that said, one should take measures to insure swelling, and water damage will not occur, or can be minimized. It is as simple as a small can of Polyurethane Varnish, and a Caulk Tube of RTV Silicone Caulk.

The 16.5 RCM has been kept cheap for more than one reason. One reason is of course to keep profits up by the company, and the others are to produce a machine that can be affordable to the masses. Should VPI themselves address every single possible issue that could ever occur to this RCM, you can best believe the price tag will rise significantly. That many of the needed modifications, and improvements can be implemented by the end user for a much lower cost.

Those issues are, needed additional cooling (fan in many instances), replacement of a poor material choice of a Cork Mat, the sealing of exposed MDF Surfaces within the machine. Nothing a weekend project, and roughly around $50 in costs to alleviate-rectify. Mark

Markd,

I had a long explanation typed out, hit submit and my computer crashed, arrgghhhhh.

Anyway I am not typing it all out again. So heres the short version.

- I was merely trying to let the OP know that if he was possibly thinkin about looking for a used machine, that he be very careful and what ever he gets may need some maintenance to get it to optimum operating condition.

- I knew what I was getting into when I bought this machine, however I was a bit suprised by what I found cause the problems it had.

- I'm not bashing VPI, I just think that on MY machine they could have done a much better job for little extra cost.

- With repairs and some upgrades (similar to what you mention above) the VPI 17 works fantastic, mechanicals (motor, vacuum, pump) are actually very well built.

- Yes the tanks (simple stainless sheet boxes with flanges) were open to the particle board (not mdf on mine anyway)

- Vacuum seal was more of a cheap soft foam seal (think cheap weather stripping foam that comes with budget window a/c units)

- I'm more of a 69 Camaro guy than a '78 but to each their own. :)

- For what it costs to get the oil changed on a Mercedes at the dealer, I wouldnt be surprised if they changed the oil pan gasket each time :):)

OP, good luck in your search for an RCM, when functioning properly I think all of the ones on the market work well (or they wouldnt still be making them), just do your homework when buying and know what youre getting and you'll happily be cleaning records for many years.

Fastxr,
I do agree, that just a few improvements could have been implemented. Although the costs of materials needed is not high, I reckon in a manufacturing process, time is money.

Let's say, that a company like VPI took a Polyurethane Sealant, or even something like that spray on bedliner material, and coated the entire interior of something like the 16.5 machine.

Probably not that much money per unit in materials, maybe what, $10-$15 at most, but the labor, and time to do such costs.

I also agree, that many folks who buy these machines aren't shadetree mechanics, (like I consider myeslf as being.) They want a plug, and play piece of equipment without these sort of unforseen issues. And I do believe that many owners have gotten the unpleasant surprise-discovery, often when it's too late, when they see fluids exiting the bottom of the machine, and find considerable internal damage due to leakage.

Or a prematurely burned out vacuum motor, due to not following some basic common sense precautions with such a machine. All of the Ametek-Lamb Vacuum Motors used in all current VPI machines are not waterproof. These motors are commonly used in commercial vacuums, and other vacuum systems, and those systems commonly use a internal baffled recovery tank.

The VPI Machines do as well, but tip the unit on its side, while fluids are in the recovery tank, and you'll introduce those fluids directly into the Vacuum Motor. That mistake can ruin, and even possibly electrically short the motor. VPI will possibly void a new warrantee if they find such evidence of misuse.

On occasion, like any other manufacturer, there is margin for manufacturing errors, and VPI has continually prooven in the past to be a company who stands behind what they sell.

Three years ago, when I was in the market for an RCM, I researched every machine within my monetary means, weighing pros-cons, features, or lack of. I did spend many weeks, if not months, and concluded the VPI 16.5 was the best personal choice for myself. I didn't desire a highly elaborate machine, with dispensing tanks, or as sophisticated, and costly a machine as say the Clearaudio Double Matrix.

I knew beforhand, that I would most likely be using multiple step cleaning processes, and thus, those added features would be in essence useless to me. I liked the fact, that the VPI 16.5 was simple, and relatively inexpensive, that in the event of a Vac, or Platter Motor Failure well out of warrantee, I could personally replace-repair those parts with not too much cost, or work.

As I close, I of course haven't forgotten the original poster, and that I hope some of my comments will help that person make the best logical choices for themselves. :-)
Mark

From the used parts inside there are also differences.
Here is a Picture from a Source Odyssey
Done in Germany, a Professional Point Nozzle System.

In the VPI 16.5 price range, the OKKI NOKKI looks pretty good. I like the idea of a float in the waste tank that prevents overflows inside the machine, metal construction material.

Demo Video
http://www.youtube.com/watch?v=zXXlxL0v78s&feature=player_embedded