VPI hw19jr Audioquest PT-8 arm G-ring 1042 cart


My previous table was a Kab Technics w/ damper, Cardas, etc and I am waiting delivery of the VPI. With a budget of around $200-250 what would be a good phono cable for this to my CJ pre amp? Also what type of alignment tool would you reccommend for this? And finally, Am I going to be happy with this in comparison to my previous table?
zenblaster
Zen,
This is common with the HW-19, and when I got my own HW-19Jr back in 1997, what I noted VPI had done to achieve proper Plinth Height, was they added one Rubber Spindle Washer underneath each Sorbothane Puck to slightly raise the Plinth height. Even in this scenario, it was a close tolerance between the Pulley, and Pulley cover. When I then went to the MK-IV Platter, which was heavier, I then found I needed to add three small Rubber Washers between the three Standoffs, and Pulley cover to keep the two from rubbing.

Or, Rubber Fender Washers (Ala Home Depot), or Metal Fender Washers, with an outside diameter of 1-1/2" can be used under the Sorbo Pucks to help you attain correct, or a higher Plinth Height. You want to insure that the belt rides in the center of platter, and I feel it is better to shim plinth, rather than to monkey with the Thrust Plate plug at the bottom of the bearing. (Lube bearing while you're at it, Mobil 1 5-30/10-30 works fine, just a couple drops on bottom of shaft, and very light coat to the shaft itself)

As for the Arm, and your cueing mechanism on the AQ PT-8 Arm, this is common, that the Cueing Cylinder will need to be adjusted in height. The entire Cueing Cylinder is held in place with one small metric Allen Set Screw at the side of the Cueing Cylinder.

To first set neutral VTA, set a record on platter. Use a folded ruled Index Card, like a little tent, set Tonearm on the lead in groove of record, set the ruled card behind the arm-Armwand, and sight the ArmWand to insure you are at neutral VTA to begin with. Adjust Arm up, and down till you achieve this neutral VTA. One can also see the Unipivot top of Arm, that it looks level all the way around to the bottom of Arm Pivot, easier seen, than explained here/ Lock Arm Mouning Post, then you can adjust the height of the Cueing Cylinder.

You must insure that the cueing cylinder picks up the Arm a sufficient amount, so thay it will clear the record, and insure when the cueing mechanism is in the down position, that the cueing ramp has sufficient clearance, so that it doesn't contact the underside of Arm Wand while in play.

belts can be gotten from any VPI dealer, or LP Gear as well. Get a new one. If I can be of further help, drop me a private mail, I'll help you.
Cheapest, most cost efficient route for a good Protractor, would be the Turntable Basics Mirror Protractor. Better choices, but more costly, would be the Ken Willis Arc Protractor, or the MintLP Protractor from Hong Kong. This Arm uses Baerwald Null Geometry

With either Arc Protractor, one should accurately measure, and insure what the Spindle-Pivot Distance is, and not assume it is at 211mm. With the TB Protractor, one will not need to know S-P Distance, but will need to accurately aim the sight line, and this can be enhanced with a piece of thread stretched from the sight line to the center of Arm Pivot. Mark
Markd51- Thanks for all your insight into this table. You gave me plenty to work on today. Fortunately my hands and eyes still work relatively well and your instruction was very clear. It is a simple table at heart and I should be able to master it in time. A few spins so far have produced a very nice sound, good dynamics and a pretty dark, noise free background. I am thinking about the Mintlp protractor, it gets such rave reviews and there is no better feeling than knowing your cartridge is properly dialed in.
Thanks again, Zen
Hi, I hate that triangle cover, and actually even VPI, I was told thinks the table is better without it ? Plus it is easier to move the belt for a speed change. I also think it looks cleaner without it. It was there to protect the pulley, but I believe you are more likely to screw up the arm, much more then you ever screw up the pulley. If you go to a good hardware store, you should find by all there screws, nut, bolts, etc... some little black plastic plugs that will fit right in the holes where the screws are. Plug the holes and it looks real nice !!