Talk to me about CAT 6 in wall cable

@daveyf this suggestion piqued my curiosity.  So, I asked Gemini.  Turns out that it’s a good thing i wasn’t trying to do this for a living!  Optical cable is too fragile on is own to be “pulled” through walls. (I suspect it would be fine if you were doing a down to the studs renovation, b/c then you can lay out the cables without the need to snake, fish or pull them, but maybe even then it might not be recommended.)

Here is an edited version of what Gemini said:

****

The cabling described by the low-voltage integration specialist is classified in the structured wiring industry as hybrid copper-fiber composite cabling. These engineered mediums are specifically designed to deliver both electrical and optical pathways within a single physical run, consolidating high-speed data transmission and low-voltage power distribution into a unified installation footprint. 

The physical installation of high-performance in-wall cabling requires careful consideration of structural mechanics and mechanical load. Standard unarmored fiber-optic cables (such as bare single-mode zip-cords) have exceptionally low tensile strength and are highly vulnerable to micro-fractures, pinch-points, and structural damage when pulled through raw wall cavities, framing studs, or conduits. As such, an integration specialist will strongly advocate for a composite hybrid cable run rather than pulling individual bare fiber strands.  
In residential networking and media integration, common composite hybrid cable examples are Structured Cable Products (SCP) HNC-EF-1 and the HNC-12 composite structured cables.

HNC-EF-1:
(1) Cat6 UTP 23 AWG Solid Copper (1) Simplex OS2 Corning SMF-28 Ultra

HNC-12:
(2) Cat6 UTP 23 AWG Solid Copper (2) Strands Multi-Mode Fiber (MMF) (2) RG6 Quad-Shield Coaxial Cables

*****

A quick Google search shows both of these products as readily available in the USA, at least in installer suitable length spools. I would think that HNC-EF1, the one with the simplex OS2, would be fine for your needs.

Obviously you need a router that has a fiber out port and an FMC at the streamer end (ideally with a LPS to power it, not a noisy wall wart).  And then Gemini warns against Cat8 from the FMC to the Aurender becasue the shielded cable can create a ground loop.

“Avoid shielded Cat8 (S/FTP) cables for this final link, as their metal shields can establish a conductive ground loop. Using a Cat6 cable ensures an absolute electrical break between the network and the audio ground plane, allowing the Aurender’s caching playback engine to operate in an uncompromised, low-noise environment.”

But i think many on here use CAT8 for this sort of purpose and don’t report any issues. I am not sure, but it may depend on whether the shield is attached at both ends and maybe whether the RJ45 sockets are metal framed or plastic.

But all this might be, I now realize, more expensive and unwarrantedly fussy than just going with Cat6 in the wall and using the double FMC optical “moat” that many of us deploy.

Anyway, when we get around to renovating in a year or 2, I am going to dive into this with a “low-voltage integration specialist.”

If you have the opportunity to run Cat6 cable, do it.  As good as WiFi is, wired connections are very reliable and you won’t have any issues with interference or signal dropouts. 20 years ago we wired every room with Cat5e and get fast 1gb throughput between and to every room.  

@kirkwallace  Well that is a bit of a surprise, as I was thinking along the same lines as your prior posts. Now, i think it is safest to just go CAT 6 and be done. 

I do know that fibre optic cable is planned for my neighborhood, and when i replaced all of my in street wiring, I made accommodations for fibre at the street to house connection. 

Since I am not remodeling to the studs, it would seem that fibre optic is out, plus I think CAT 6 is all that the Aurender style units require. I will probably put two lines in, one for Roon and the other for the server. 

Sounds very sensible, @daveyf . (But i still like having the fiber moat before the Aurender.) It’s probably over kill, but i also fiber moat my Roon core. 

Good morning,

I’m not going to weigh in on which cat of Ethernet to choose, personally, I have double runs of cat 6 cable run to all of the rooms in my house. The reason for this is that in the future, if you have work done in the room, mistakes happen and lines can get damaged and then you’ll have to re run and possibly open up your finished walls again. 
Running double runs of Ethernet cables in your 1 room is relatively inexpensive to do when the walls are open. 
 

Good luck with your room.