Isoacoustics Gaia and speaker wobble

Yes, as I understand it this is part of the design.  Did you notice in the instructions it wants you to have them unscrewed partly (so there’s a gap between them and the speakers - they should not be screwed on tight) and also with the letters on the units facing either forward or backwards?  They are supposed to have movement.  I watched a video with the designer and they said they are directional in this way - that is, the speaker drivers have a pistonic effect that moves forward and backward with the speakers (front to back), and the Gaias move along with that.  Now, if the wobble is the same as if you had speaker spikes on hard floor for instance, that were not leveled out properly, I would be concerned about the installation.  

I watched you video, there is lots of movement.  It looks like the spikes are moving up and down on the carpet pad.   Here is a picture of mine.  The Gaia are on a hardwood floor which is on top of concrete.  The Gaia kind of suction cup to the wood floor.  When nudging the speaker, there is no speaker movement side to side, nor front to back.  Nothing like what your video shows.  I guess it kinda feels like the speakers are on furnature felt pads, ie. they will move a few mm, but, it is not really perceptable.   My guess is that you are not getting all the performance that you could.  As you know carpet also has a pad underneath.  You might want to try longer spikes, or better yet, show that video to Isoacoustics and see what they say about all that movement. 

I don't have them, I just thought I would share this recent positive experience at the NY Audio Show

3. Isoacoustic Isolation Feet, I heard the difference in their demo on carpet

https://isoacoustics.com/home-audio-isolation-products/orea-series/?gad_source=1&gad_campaignid=22978080468&gbraid=0AAAAAClQro92imFHI0CQPY6UW0qAAQBZh&gclid=Cj0KCQjwsPzHBhDCARIsALlWNG2VxQmcaYWKW-9IIDbqmbmANs7JBB9pZvso0lK93PlZxbaxXm-_xssaAsH2EALw_wcB

They had two pairs of identical speakers, volume matched, I think these Operas

https://www.operaloudspeakers.com/en/

One pair on their isolators, the other not, and a customer could randomly switch with a remote control. A duet with a female singer and Leonard Cohen, I could definitely hear a change in Leonard’s voice each time the customer switched, the pair on the Isolators sounded better to me each time.

@hazeloop 

I think the problem is the spikes on the carpet are not solid enough. I have Gaia ii footers on my Kanta 3 speakers on hardwood floors are they don’t rock near as much as yours appear to. Did you try without the spikes ? Or maybe a platform under the Gaias? 

@hazeloop

Note:  In my post and picture above, my experience is with the GAIA I, not, the GAIA II.  The speakers are Wilson W/P 8 that weigh approx.  170 lbs..., so, the GAIA I is required.  I am assuming that the GAIA II should behave like the GAIA I, but, that may not be a good assumption on my part --  Although, in your video, it looks to me like the carpet spike is moving up and down with the carpet/pad, and it is not the GAIA II that is controling the majority of the rocking. 

I think you have to figure out if the 1 inch spikes on Isoacoustic carpet spikes are long enough for the carpet and the pad.  Even if they are, they may not have pierced through the pad.  You could mark where the spikes should be, then, take the speaker off and use a hammer to make sure you drive the spikes through the carpet pad.  Then use your hand to press down the spikes to make sure they consistently hit the floor and do not wobble.   Even if the spikes need to be longer than 1 inch, if the hole through the carpet pad is done, the weight of the speaker may be enough to compress the pad and make sure the spikes hit the floor.