Are the MF308 and MC402 matching together ?


I got the Pre-amp Musical Fidelity 308CR and power-amp Mcintosh MC402. They sound great so far. Suddently I just read about the preamp - poweramp mismatch and just wonder are they perfect matching ? Cos I don't have a change to have another pre-am or power amp to compare... The preamp MF308 has specification as follow :
Voltage RMS, maximum > 30 Volts
Power maximum > 5 Watts
Peak-to-peak output current 0.5 Amps
Impedence 50 Ohms
Frequency response 20Hz to 20kHz ±0dB. 10Hz to 100kHz +0, -1.5dB.
LINE OUTPUTS
Total harmonic distortion + noise, 20Hz to 20kHz > 0.0035%
(5 Volts output, maximum volume).
Signal / noise reference 1 volt RMS output 104dB ('A'-weighted, at half volume)
Input sensitivity for 1 Volt RMS output 240mV
Input impedence 47k Ohms
Gain at maximum volume 12.5dB (4.2 times)
Overload margin 31dB
Channel separation > 88dB typical at 1kHz, maximum volume
PHONO INPUT
Frequency response reference IEC RIAA See graph below.
Signal / noise reference 1 Volt RMS output > 95dB Moving Magnet ('A'-weighted, at half volume).
> 85dB Moving Coil ('A'-weighted, at half volume)
Input sensitivity for 1 Volt RMS output 2.5mV Moving Magnet.
350µV Moving Coil.
Input impedence 47k Ohms
Overload margin 31dB

The Mcintosh MC402's specification :
Power Output 8 ohms 400 w @ 8 ohms
Power Output 4 ohms 400 w @ 4 ohms
Power Output 2 ohms 400 w @ 2 ohms
Power Bandwidth 20 Hz to 20 KHz
Total Harmonic Distortion 0.005 %
Intermodulation Distortion 0.005 %
Dynamic Headroom 2.1 dB
Frequency Response 20 Hz to 20 KHz +0.0 dB / -0.25 dB
Input Sensitivity 4.0 v
Signal to Noise Ratio 115 dB
Damping Factor 100 @ 4 ohms
Input Impedence 20 KHz
Power Requirements 120 v 10 A
Warranty (parts) 36 month(s)
Warranty (labor) 36 month(s)
Dimensions 24 cm. H x 44.5 cm. W x 51 cm. D
Weight 50.1 kg.

How can I know they are perfect match ? Or should I change the pre-amp to ultima the sound of MC402 ? Appreciate your idea. Thanks
Vincent

vincentdlee
I am an electrical engineer so I know the problem you speak of very well - you can believe what I told you. I have done research on impedance mismatches and how they affect traveling waves and what the optimal resistace/inductance and transconductance/capacitance ratios have to be for distortionless transfer. The issue is that you are taking "rules of thumb" as gospel. When people say the impedance ratio should be 10x, they mean AT LEAST 10x. This means that 200x is MUCH BETTER than 10x. If you had 10x, it would not be as good as what you have now.

In truth though, it depends on the impedance curves and not the values quoted on the brochure. I have seen systems with an impedance ratio of 1x and it be fine because the curves didn't hit each other. The fact of the matter is that the 10x rule is just to be sure that the impedance curves are far enough apart to not hit each other. The farther apart the better - and 200x just makes it all the more impossible for the curves to interfere.

Secondly, a second system for comparison is nice but how do you know that one is the best? Well, you don't! There is nothing perfect and there is no absolute. All you can do is experiment until you are happy.

Your system is just fine. Enjoy the music! take care, Arthur
Iagree with the above...not technically minded but if it sounds good..you are all set....the only way to hear a difference is to try another preamp like a Mac c46 etc.
Thanks Aball, you should be right then... by the way, I think that cos I have a not very good CD player in my system, that's why I got a deep feeling with the system at the show... I intend to upgrade soon but have no idea at the moment... My CD player is Marantz 1040, maybe no longer available on market now, but I really like it's sound, even though technically in manual, it said just 1 bit CD player. Just curious... could you tell me how different between 1bit, 16bit and 24 bit CD player... and 96Kz, 192Kz as well... so many things make me confusing when select the better CD player to upgrade now...