Soulution amp and tubed preamp

Hi

That`s great news about the Coincident being able to drive a
a low impendace input poweramp. I`m planing to use mine with a 10.000 Ohm input amp and I have been worried about a missmatch.Very much appriciated. Thanks Al and Charles.
I read everything that you both write, and learn a lot.
My system has been down for 7 months now, but I´ll be back enjoying Music in a couple of weeks when my new source and amp arrives.

Cheers

Psag, demo a VAC Statement or even SigMK11a if looking for a tube pre for Soulution amp. It will have no problems driving it.

What necessary works doesn't mean good SQ. Last year a local audiophile demoed several tube pre for his Soulution amp but ultimately settles on Ayre KX-R. He couldn't find a VAC pre to demo ...

Do you have access to Vitus by any chance? Both Gryphon and Vitus are well regarded amps. I cannot say if Soulution would work for you on work, but I can understand why you are asking the question. Hence, why I suggest additional options you may wish to consider. You may also wish to consider Constellation or D'Agostino. If you like the clarity and effortlessness of the Soulution but are wondering about having more than enough 'note saturation', the D'Agostino Stereo amp is also a very nice choice.

I haven't heard Gryphon. I heard Soulution at RMAF with Focal speakers and was impressed with the clarity and effortless presentation. But I listen to a lot of rock music and I wonder it would sound lean.

Hi Psag, I am sure there are higher input impedance SS amps that you could look into besides Soulution. For example, Gryphon amps are 20kohms (balanced) so you'd likely be in safer waters with your ARC preamp. Not the same character as a Soulution but do let us know what other amps you are considering. Good luck.

Hello Al,
Well that makes plenty of sense! The transformer coupled Coincident would
avoid the potential wide impedance fluctuations of a capacitor coupled
preamplifier. Pap's experience isn't the odd exception after all and his
success with the Soulution amplifier is now logically understood.
Thanks,
Charles,

Hi Charles,

As you know the CSLS has transformer coupled outputs, which I suspect maintain a fairly constant output impedance across the audible frequency range. I'm pretty certain that the ARC Ref amps have capacitively coupled outputs, which causes their output impedance to rise significantly at deep bass frequencies.

As I'm sure you know, it is often recommended that there be a minimum of a 10:1 ratio between power amp input impedance and preamp output impedance. And to be safe that ratio should be applied to the preamp's highest output impedance at any audible frequency, which especially in the case of capacitively coupled outputs may be much higher than the spec provided by the manufacturer, since unless otherwise stated that spec is probably at a mid-range frequency. Or if the preamp's highest output impedance at any audible frequency is not known, and there is reason to believe that the outputs are capacitively coupled, a much higher ratio than 10:1 should be applied to the manufacturer's spec. I've suggested 50 or 75 to 1 in past threads, to be completely safe in those situations.

The adverse effects which may result from failure to adhere to that guideline, such as rolloff of the bottom octave, result mainly from the COMBINATION of substantial impedance VARIATION as a function of frequency and the low ratio, not just from the low ratio in itself.

I see, btw, that ARC's web page on the Ref10 which Psag indicates he is using does in fact have the same 20K minimum load recommendation that I indicated earlier applies to many of their models.

Best regards,
-- Al

Psag,
Al gave you very good information. Here's an exception to the rule. Australian member Pap said he used a Coincident Statement Linestage quite successfully with a Soulution amplifier. The Coincident has an output impedance of 500 ohms. So an unexpected outcome given the numbers. Al's point is certainly the general rule of thumb is these situations. I have no idea why the Coincident is an odd exception.
Charles,

Makes a lot of sense to me. Thank you Al. BTW, its the Ref10.

You didn't mention the specific ARC preamp model, but my strong suspicion is that it would NOT be a favorable match. Typically the output impedance of the ARC preamps having 600 ohm specifications rises to significantly higher values than that at deep bass frequencies. See John Atkinson's measurements of the Ref5 SE for example. In combination with a 4.7K load that rise will result in at least a slight rolloff of the bottom octave.

Also, ARC recommends a minimum load of 20K for many and perhaps most or all of their preamps having 600 ohm output impedance specs.

You are considering an amp whose design is based on a no compromise approach. I would not introduce a known compromise, however small, into its application.

Regards,
-- Al