2. analog
  3. 1269027757

Azimuth observations and importance

After adjusting azimuth with a Fozgometer loaned to me, the following is what I observed. Individually, these changes were subtle although noticeable. The combined effect however, was significant to the overall presentation.

Imaging improved.

Vocals became more focused, not as big and wide as before.

Instruments more detailed with greater air. Location is more precise.

Tighter bass versus the slightly lingering bass notes previously.

Better top to bottom detail and clarity.

I never realized how important correct azimuth adjustment is and this exercise was quite a learning experience for me. Thinking I was correctly adjusting azimuth by visually setting the headshell as level as possible was a reasonable but flawed attempt.

I have found at least two stylus issues that if present will affect azimuth and sound.

1) A straight cantilever that is twisted left or right changes the attitude of the diamond and its relationship to the groove. By twisted I mean the cantilever has rotated on its own axis. This one is very difficult to see without appropriate magnification.

2) A cantilever that is canted to the left or right a degree or more but is still straight, not bent. It points left or right probably because it was not centered correctly when the cantilever was installed. It also changes the attitude of the diamond.

What is probably basic and common knowledge to everyone here is something I have just been enlightened about after giving it very little thought. I am now convinced that accurate azimuth is a required step in the turntable set up process and I will be giving full attention to this part of the equation.

No more guesswork and eyeballing which I am embarrassed to say was the norm. Doug
128x128dougolsen

Showing 6 responses by actusreus

actusreus
733 posts
 
Elizabeth, I always enjoy your advice. Do you know how to precisely use a voltmeter (or a multimeter I can get for about $20 from Ace Hardware) to adjust azimuth?
I was told you put the leads to the speaker's terminal but mine are bi-wired and I'm still confused about the DC/AC current selection. I checked out the Fozgometer and it looks very straightforward to use; so straightforward in fact that I'd be probably willing to spend $250 to get the damn azimuth right once and for all...
actusreus
733 posts
 
So, for the cantilever canted to the left or right, what's the solution? The cantilever on my Soundsmith Aida cart appears to be very, very slightly canted to the left (toward the center of the record) but is perfectly straight. I have a test record but without voltmeter it is very difficult to hear whether the output varies between the L and R channels. The test tone sounds fine and even. I tried leveling the head shell but then the bottom of the cart doesn't look parallel to the record surface. In the end, I went with Fremer's advice and used a mirror to make sure the cantilever itself is perpendicular to the record surface. Not surprisingly, the head shell is not parallel now.

Seconding the first poster's question: what was your ultimate setting? The cantilever perpendicular to the record surface, head shell parallel to the record surface, or something in between? And how does this device work? Would a voltmeter be equally precise in your opinion?
actusreus
733 posts
 
Thank you very much Jtimothya! I actually do have a test record so I'm more or less half way there. Is it me, or is the azimuth one tricky bastard?:)
actusreus
733 posts
 
I was wondering if anyone could give a succinct (if possible) tutorial on how to use an analog multimeter to adjust azimuth for someone with no engineering background (in other words, azimuth for dummies as it were). In the alternative, perhaps someone could point me to such a resource. I have Fremer's tt set-up DVD but it's useless in this regard. It would be greatly appreciated.
actusreus
733 posts
 
Thank you Lewn. This certainly gives me a better idea. I am also confused with how and where to insert the leads in the system and DC vs AC voltage on the multimeter. Do I insert them in the amp's speaker terminals or in the speakers' terminals? Do I remove the speaker wire completely when doing this? Any risk damaging anything while messing with the leads? Moreover, I recall Fremer talking about low voltage and high voltage for each channel. I am a fast learner but need to master the basics first...

Thank you!
actusreus
733 posts
 
Thank you all for your input and advice. It's greatly appreciated!
More to discover