recommend full featured preamps?

Stick with the mcintosh.. Not even close to carver, carver is okay for 300 bucks used, but sometimes no remote, and the loudness turned on sounds like you are hitting a plastic garbage can in the garage... They have that goofy other mode I forget the name it adds some nice effect, some natural noise thing or something.. Harmonic something or other...

Anyway most of your Preamps with Bass only knob is just a 100 hz boost.. But with a mcintosh pre you get the 5 band eq, which the bass range knobs start at 30 hz which is very low and very nice to get that just slight bump in the room loading feel like a subwoofer, and then you can kick up the 80 hz as well, and the 120 hz range in the mid bass etc...

And Mcintosh has the variable loudness knob, so you can choose how much db in loudness you want to add, not just an on full blast loudness or off button. And the mcintosh sounds more full and warm in the SS realm nearly tube. And resale value in most cases is better you would barely loose anything if you decide to move on again.

Carver pre-amps like the c-6 have a lot of unique features that you may or may not find useful. I'm sure Mac does as well, but I am reasonably certain that each has a different set. So it is not an apples and apples comparison if you are looking for particular types of flexibility. You need to do the research and determine, if that is the way you want to go.

A separate digital equalizer device like the BEhringer suggested by Vegasears will cost more as well but could prove to be most effective, at leat for digital sources if not analogue, if needed.

Loudness is one of the more useless features on the Carver as it is with most preamps. I've never used it. There are many other unique features you will not find elsewhere that I have used to very good effect from time to time. There is greater flexibility in adjusting the tone controls using a tilt feature in combination with the actual tone level controls that you will not find elsewhere and I have found to be quite effective in getting levels set just right when needed without a separate equalizer.

There is nothing on the Carver that deals with "natural noise" that I am aware of, though I'm not sure exactly what that means.

You might find a Carver in good operating condition for $300. You won't find a Mac most likely in that range. If the cost is not a concern, get a Mac if that is what you prefer. A Carver c-6 pre sold for $900 almost 20 years ago, so it was never "cheap"...it is a very respectable unit. It has held its value pretty well over time I would say.

I been very satisfied with mine for almost that long. The only piece I own that I've held onto for longer is the Linn Axis turntable.

Mapman,
I remember now its called the "Holography" circuit... Its pretty nice for those compressed recordings...
I was not really knocking the carver as it is for the price its not bad, you can find some of the Mcintosh pres for 500 to 700 with all the features from the late 80's early 90's same era that are a bit better for a couple hundred was all I was illustrating.

As for the Behringer its okay, but really a cheap piece that is a pain to work with for most people, too many gadgets and features that have nothing to do with straight 2 channel full range speaker useage, and results will vary with much time needed to sometimes get dialed in or be effective correctly.. And then buying one used for 150 or 200 bucks might as well go with a mcintosh, its a better unit period in my opinion, well built, and eliminates all the EXTRA cables and conversions from XLR to RCA using a unit from the Pro audio realm...

Undertow,

The Carver holography circuit is what I thought you might be referring to.

It has nothing to do with compression or dynamic range. If your system lacks transparency, think of it as a magic "transparency" button.

technically, it reduces crosstalk between channels. I suppose crosstalk would be considered a form of noise and that circuit then a form of switchable noise reduction.

Wouldn't surprise me if many other newer amps that sound inherently transparent do something similar internally to achieve it. The most unique thing about the Carver is the circuit can be switched in or out as needed. That is the flexibility aspect of it. And yes, it does work exactly as advertised. The tradeoff is a small change in the timbre of the sound, particularly in the mid-range.

I used to use the holography circuit but then realized there were other ways to coax more transparency out of my system that I pursued (power conditioning, interconnects, setc.). Now I do not use it much. But it was nice to have around back when I needed it.

The features I still find most useful on the Carver today are the two switchable circuits for separate signal processors. I use 1 for a dbx range expander that still comes in handy with dynamic range-challenged recordings.

Also, the tone tilt feature I mentioned can be useful to provide flexibility in adjusting tone/timbre in ways not possible with conventional tone controls.

There is an absolute phase shift circuit that can help with the low end if needed, depending mostly on room acoustics.

The blend control can also be useful. It provides the ability to continuously increase or decrease channel separation all the way from mono to greater than normal.

I find I use these features very infrequently these days (the separate DBX the most because many recordings just have the dynamics sucked out of them before they even hit your system) but they have been invaluable tools to help me get my system tuned in better over the years when needed.

Also, the low cost for the Carver used today is a big plus. It provides lots of features but sounds VERY GOOD even without them. Over time, you may find ways to tweak your system using it that results in not needing the flexibility in the pre-amp anymore. Then you might look at moving up to something even better, though I truly believe the C-6 is nothing to sneeze at in regards to sound quality.

I'm almost to that point myself. If I can find a SS amp or hybrid with sound that is more like the tube emulation outputs on the Carver than the SS, and I can use my DBX without issue when needed, I think I am golden. I haven't quite decided what that is yet though, so for teh time being, my Carver is still the man.