Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
B_limo: several posts ago, I already linked to the wall wart that I own. George speculated that it is an smp. I've searched and searched and there's no published info to confirm or deny. George suggests the AM radio test, but I'm not buying an AM radio just to do this test. To be blunt, I have little motivation, since the differences between my wall wart and the TeraDak are so clear. If, theoretically, there shouldn't (couldn't?) be much difference between linear power supplies, then the conclusion to draw is that I must own a smp wall wart. If someone wants a stronger argument then that, well, they can try it out for themselves--as you have suggested you will with your battery supply.

fyi: for my tests, I used a cheap hospital grade power cord. Whether one could do even better with a better cord, I'll leave that to those with deeper pockets than I to determine.
Not all linear power supplies are created equally. B_limo makes a good point as to the LSA not requiring a lot of current, and the LSA has it's own regulation, but any power supply can introduce noise into a system. If this Teradac somehow reduces the noise level then it should be quite apparent as Banquo indicates.
My bad Banquo, didn't see the link, didn'tknow you looked into it at all, let alone actually digging around a bit. I apologize. I'll check the link, but like I said, I'll probablyend up just buying the terradak to back up my battery pack and will report back.

George, two questions: does the lightspeed ever need to be recalibrated? It seems like my volume control may be adjusting in larger increments than before...

Question 2: is it okay to dress it up a bit? I was thinking about a small wooden case or having it professionally painted.
01-15-14:
B_limo: George, two questions: does the lightspeed ever need to be recalibrated? It seems like my volume control may be adjusting in larger increments than before...

Question 2: is it okay to dress it up a bit? I was thinking about a small wooden case or having it professionally painted.
B_limo

Q1: Only if any part of the rest of the system has changed with a different gain to it source amp or speakers. As it's impossible for the Lightspeed Attenuator to change gain as it has none.

Q2:As the Lightspeed chassis is part of the RF shielding, puting it into a wooden case may introduce rf noise into the system.I advise against it.

Cheers George
Thanks George.

What about painting the exterior chasis of the lightspeed with automotive paint? Yes, no?