Andy Kim - Needle Clinic


I wanted to put this post out there about Andy Kim of Needle Clinic, located in Bellevue, Washington. As many may know, Andy is a cartridge re-tipper. I tried to find some older posts to add my comments but couldn't find them. So I'll start another OP. I just got my Lyra Kleos back from Andy today. Here's my comments.

My Kleos sounded a little off lately, so I thought it should be checked out. I sent it to Andy Kim. It turns out all that was needed was the stylus required a cleaning and polishing. Andy reported back that the stylus only has about 10 percent wear; IOW plenty of life left.

So I remounted the Kleos today and have been playing all types of music: rock and roll, classical, and so forth. The Kleos sounds wonderful; just great. Kudos to Andy Kim.

Fyi -- some may ask why I didn't send it to Peter Ledermann at Sound-Smith. I seem to recall reading somewhere that he's been unusually busy lately -- and with good reason -- and turn around might be a bit delayed. Also, I'm not sure Peter uses replacement cantilever/stylus assemblies that match (or at least come close to) the original. Andy does.
Anyway, that is a bridge I don't have to cross today.

Bottom line: Andy turned my cartridge within a week of receipt and I am pleased.
bifwynne

Just received and remounted my Benz LPS, which was "rebuilt" (new boron cantilever and line contact stylus) by Andy Kim. This is the third time I’ve used his services. I sent him this LPS due to high hours (almost 1000 hrs) and an unfortunate incident where I literally stabbed myself with its cantilever. (Ever have to clean flesh off a cartridge? It was surreal.) There was less than a one week TAT from me sending it off to Andy and getting it back. To be succinct, the LPS sounds fantastic and to my memory as good as it was when new. This is the third time I’ve used Andy’s services (Benz Gullwing, twice with Benz LPS) and again I am very pleased with his fine work. TBH I don’t see myself using Soundsmith again, not because SS are inferior, just because of the long TAT.

This is a short review of the excellent and quick work done by Andy at Needle Clinic in LA. I sent him my Dynavector Karat 17D3 for re-tipping and had it back in less than a week sounding better than the original, particularly in terms of stereo signal balance and overall tracking. 
Andy was professional and clearly a total craftsman.
 

Great to see your report on the satisfaction being met as a result of having a Cartridge overhauled by a rebuild service.

The turnaround time when delivered in a short period is an absolute bonus, and my take on it is that  memories of what was temporarily separated from are strong and the benefits of the service undertaken are quite noticeable when recollecting and assessing the new performance on offer.  

My experience mirrors yours as well, with a Cartridge Rebuild from a different supplier of a rebuild Service.

In my case I was able to compare the the returned Cartridge to a identical model.

The returned Cartridge was mounted on a detachable Headshell.

Another Cartridge of the same Model with a few hundred hours of usage was also mounted onto a identical Detachable Headshell.

Both Cartridges were A/B Compared in a identical set up and the returned Cartridge from the rebuild service without any run in time, shone out as the better Cartridge over the original model, to the point that the Original Cartridge was said to be quite lacking in qualities as a comparison. 

The knowing that the rebuilt cartridge was to improve further was very satisfying.

All

I would like to provide my feedback about a fantastic experience with Andy Kim as well! I recently pulled out my old Accutrac 4000! for the past 30 years it was on display as a conversation piece.  Feeling a bit nostalgic, I connected it and found it worked perfectly except the stylus was in bad shape, but the original LMA 1 seemed to be ok.  after an exhaustive search I determined I could not find a replacement stylus or an original ADC cartridge.  Most suggested, replacing the cartridge completely and forgoing the functionality that made the Accutrac appealing 40 years ago.  This wasn't an option for me.  This led me to explore   retipping as an option. The initial contacts I made informed me I the process could take weeks to as much as a month to send in and expect a return.  Then I contacted Andy.  Andy responded promptly and was also local!  He retipped my original LMA 1 in 2 hours while I waited!  I suspect that others I contacted ship out the work as opposed to performing the work in house.  The new stylus (Micro Ridge Boron) now rivals my main Turntable (Music Hall IKura with a Orthron  2m Black cartridge)

Many tanks to Andy for his great work and prompt service!!

These are great reports, keep them coming.

These services need recognition, especially as there is a very cost-effective route into owning a high quality and design Cartridge, if the right donor model can be discovered for fair monies parted with.