2. cables
  3. 132597-2647

NEW Cerious Technologies Upgrade - Graphene Matrix Cables

CT Graphene Matrix Cables:

I have been using the CT GE cables for almost two years.
I recently traded up for a full loom of CT Graphene Matrix cables, including speaker, interconnect and PCs, and I wanted to share my experience. I started by replacing only the ICs to try and hear the differences.

The new Matrix interconnects sounded better than the GE immediately after install. I found the original Graphene Extreme ICs to be good but not on the same level as the outstanding GE speaker cables. As break-in started to clear things up, I can hear more clarity and detail not heard before. The ICs are incredible on their own and at the 30 hour mark, I can hear a clear superiority over the GE ICs. I recently started using the Teo Game Changer ICs and preferred them over GE but the Teo has now fallen to the new Graphene Matrix ICs. My Teo’s were and are great, and it is stunning to experience Cerious Technologies commitment to making great technology better.

On the third day of listening to the GM ICs. I couldn’t wait anymore, Having too much fun. I then installed the speaker cables and power cords once I had a pretty good feel for the sound of the GM ICs.

With the full loom of GM cables running in they are going through some strange changes and definitely need time to settle down before realizing what they can really do and very important Bob says to not move them. Since I have a home office I can let them run in all day. I’m at around 120 hours now and they are still improving. Here’s what I’m hearing:

Extended highs and tighter lows.
More detail and better low level listening
Drums are tighter, more clearly defined. So real is the snap of the snare drum. The bass has more depth, seemingly goes deeper, lower. This aspect stands out the most.

I am not in the industry, I’m not an engineer, I don’t work for Cerious Technologies, but I am a fan of the cables and am enjoying what my system is capable of.

I’m closer to my own pinnacle of sound reproduction than ever before.

Lance

lancelock
t_ramey
632 posts
 
@yoby 

Wow, good to know about the FI-28 R. I usually get my bulk cable, at least the Furutech, from Chris at VH Audio. He’s always got good prices and ships fast and is a pleasure to deal with. 

I’m wondering if the contact openings on the FI-28’s are large enough to take the wire from the Matrix? They should be similar to the NCF’s, you think?
elixir
13 posts
 
Has anyone tried to replace the stock connectors on the Matrix? If so, what with and how did it sound?
maxima95
289 posts
 
The FI-50 and the Viborg specs say they accept a cable up to 20 mm.  The FI-28 is specified up to 17.5 mm.
t_ramey
632 posts
 
Thanks maxima95. That size probably does make a difference. I was thinking even the barrel opening might not be large enough on the FI-28 for the large diameter of the Matrix. 
genjamon
96 posts
 
I feel the need to comment on the connector issue here.  The one of my four PC's that had an issue was due to the Furutech FI-50 carbon connector (non-NCF material, but otherwise the same as the NCF design).  There was buzzing noise and a puff of smoke from the connector before the power conditioner's circuit breaker tripped.  After removing from the system, I opened up the connector, and it appears the spacing of the screw terminals for the wires are wider than with the stock Viborg ones.  This made it pretty hard for Bob to route the wires from his thick/stiff Matrix wire bundle into the screw terminals and secure well.  It makes any torque you put on the power connector more capable of pulling the wires out of their screw sockets and potential for short circuiting.  This appears to be what happened in my case.  

As a result, I'd be very careful about these Furutech connectors, making sure there's enough wire slack for really solidly securing them in screw terminals, and adequate wire insulation between Matrix wire bundle and screw terminal itself within the housing.  The very heavy-duty thick and stiff Matrix wire bundle creates quite a bit of torque on the connections as you bend it around to deal with system angles.  
More to discover