Looking for a power cable upgrade


I got an itch to upgrade. The sound I'm getting now is great I like it but like most of us I'm want to look at the other side of the mountain for some thing better. This is what I'm using right now:
http://www.vhaudio.com/acrolink-7n-p4030.html
Im looking at spending around 500.00 per cord either used or new, and also would try a diy solution. If anyone as used my current cables and has moved to something else please comment. Or if you have found something fantastic please comment as well. Any input would be great. 
manwich620
my final chirp....

(1) putting in dedicated power lines with armoured cable was a quantum leap upgrade in performance when compared to the effects of the power cable itself. Power cables by themselves without doing this may be an improvement but only a comparative  small one at best. Complete the cradle-to-grave power upgrade  with an upgrade starting at the panel first.

(2) contemporaneous with the dedicated lines (a separate one for the amp and another separate line for the source) I also upgraded the wall plugs to --

(1) first, to Hospital grade plugs, --and then--
(2) further upgrade later to expensive audiophile grade wall plugs.

The latter are gold plated high grade pure copper with no nickel, brass or ? Components ( gold plated is oxidation resistant but pure copper is VERY soft .. So be careful and don't bend them cuz it's very easy to torque them and thus do so...)

The latter new plugs are a further incremental "last step " upgrade  to the hospital grade wall plugs, but only on my "A" system would I say they are worth  the added not insignificant cash outlay.

(3) Power conditioners -- a potential BIG limiting effect and crappy resolution limiting clouding veil.

Sure ... In some circumstances they may prove fruitful if you live in an area with wild power swings or crummy old wiring blah blah  etc.

HOWEVER... a dealer twigged me in to the tip that many high-end gear with their robust power supllies do NOT need NOR WANT any intermediate PC insertion ... The latter can actually be just a messy added limiting filter that creates a step-down in resolution.

He personally demonstrated it to me in my own system in MY home .... Damned if he wasn't right to the step-down of a PC in MY system. The performance downgrade with the PC in was not subtle. 

YOUR TAKEAWAY.  : be careful... It's no "one size fits all " here either ...

Again ...a PC is  VERY system dependent in the first place, and maybe even an entirely avoidable step-down in a high-end system with its inherent robust high-end  power supplies.

I fully agree with AKG.  If there is any way you can upgrade the feed from your panel to the wall socket, you will gain immense sonic improvement at all your equipment.  I had a Rega Osiris too.  I had a lot of mechanical hum out of the toroid coils coming from my dirty power.  I installed a 1/2" emt conduit with 10AWG solid wire from my panel to a metal box with Porter Port receptacles in the wall.  OMG.  Everything jumped in performance.  Some much more bass, clarity, immediacy in attack.  Everything was better.  But, I still had hum from the DC offset on the lines. 

I then bought an Isotec Syncro cable.  The one with the huge barrel which I assume is a Capacitor in line.  That took all the hum out of the toroid coils.  It even smoothed a little of the hash of the top end of the Osiris.  It made the whole thing better.

However, I moved onto a Conrad Johnson Premier 140 amp with the Teflon upgrade.  The Isotek took the hum out of that amp too.  However it clouded that amp too much.  Put a veil over the music.  I then bought a Topaz 2.4 KVA line isolation transformer.  I installed that in the basement inline with another 1/2" conduit and 10 AWG wire.  This cut most all the hash out of the CJ amp and did very little to veil the music.  However my First Sound Mark 3, Allnic HC1201 did not like it.  They want pure unfiltered power.

In short, if you can better your power from standard 12AWG romex in the wall to  metal enclosed 10AWG you will gain a huge jump in performance.  A day of labor is about $500, materials about $250.  Provided there is access from the panel to your gear.   Now every change in power cables will be much more noticeable.  I have a mix of Signal Cable, Cullen and Sillnote.  They are all decent for the money. 

I decided to go with the same cable but as a diy. I having a hard time putting it together. Anyone here in the Los Angeles area that can help put it together for a fee?