FM antenna made simple


I have a Rotel RX-975 receiver that cuts in and out when listening to local FM stations in Hartford. I am using the supplied "T" wire antenna simply taped to the wall behind the receiver. How can I improve my reception without getting too complex ? i.e without getting up on the roof or climbing the chimney to install a rotating antenna.
loshinskie0c67
Thanks for the conformation, Sw. You know us neurotics. I actually put the antenna up because I was tired of the 6bucks going to Direct Tv./for the local channels ea. mo. I did buy their (RS) amplified 29 or 39 job= not nearly as good as the 19/outside one. I bought my present fm tuner from Nanderson/ I figure him to be an fm god.I was embarrassed to ask him about a tv antenna/for FM.
Swampwalker,
I might be mistaken, but I had a "stick" from Radio Shack, and it was rather lousy. The Terk is very good. Of course we may be thinking of two different antennae, but I don't think so.
Sean,
Wow. Thanks for taking the time to respond. I printed out your directions and will read them in detail. I'll let you know how it works if I go that way. Will also consider the Terk. Thanks to all for the responses
An indoor antenna may or may not help you in this situation. Unlike AM, antenna mounting height will make a large difference both in FM sensitivity and multipath rejection. Another factor to consider is whether you need a directional array to capture these stations. Before investing in any antenna, I would suggest making some walkaround reception observations with a high quality portable monaural FM radio in your listening room. These units, being mono, generally surpass all but the finest stereo units for sensitivity and selectivity. I have used the GE Superadio II for this purpose with very good results. This should give you an initial indication of whether reception is possible for this location, the 'hot spots' in the room for best reception, and what directionality, if any is needed. Don't be upset if you find that you simply cannot get good reception - occasionally an interior room will simply not permit satisfactory reception. My own listening room has very poor FM reception and I am forced to go outdoors. If you are lucky enough to obtain decent interior reception, try to stay with a passive antenna. Believe it or not, the humble 300 ohm "T" is one of the best. Sean's homemade design is very good also. While some have had success, I am not a big fan of the $100 designer interior antenna, and think even less of the Radio Hack models - many having built in amplification that simply mangles any signal. Don't forget to take the "T" right up to the ceiling, the higher, the better. If you cannot obtain a satisfactory signal from the "T", you probably won't get it with any other interior unit and may have no choice but to go higher and perhaps outdoors (if you simply cannot leave the room, then your only possible option is a better tuner, which in virtually all cases represents very poor value per dollar over a better antenna). While this may not require a roof mounted array, you might first consider an attic-mounted or exterior wall mounted omnidirectional unit. The Fanfare omni is quite good - and so is the $20 Radio Hack "X" model. If you have a drop ceiling, you can sometimes fit the "X" above it, with varying results. But these units perform best outdoors. Remember that ANY quality outdoor antenna, properly mounted, will outperform any interior model, period. If you have a multipath issue or require maximum gain, then you may be forced into a directional unit, which may require roof or obstruction free mounting. Radio Hack outdoor antennas are OK, but not great value, IMHO. The better, sensibly priced, outdoor models can be found from Channel Master and Winegard. A couple of other pointers if you're serious about this: First, unless you are prepared to buy the very best (i.e. Blonder-Tongue, Channel Master, etc.), avoid all RF amplification - most do a horrific job and impose unacceptably high levels of noise. A quality, low-noise FM amplifier can run upwards of $200. Unless you really live on the fringe, most folks simply don't need them, and the money spent on amplification is better spent on a larger or better passive outdoor array. Second, if you have a lead in run under 20 feet, you may use 300 ohm twin lead (this has the lowest loss, but is generally unshielded and will pick up noise). Ideally, shielded 300 ohm cable is the very best for this application, but is nearly impossible to find anymore. If you have a longer run, the shielding of 75 ohm coaxial outweighs it's higher loss rate. Remember too to use only RG-6 coax, as RG-59 has a very high loss rate. The good thing about basic radio reception (raw sensitivity and selectivity, not all those other qualities we associate with high end tuners) is that the antenna is 90% of the deal - an average tuner with a great antenna will run rings around the very best tuner with a poor antenna. The latter part of this response admittedly exceeds your question, but may be of some help should you decide to attempt a more complex installation.
I have to agree with Sgmlaw here for the most part. Getting a good outdoor antenna mounted up high with a low loss feedline that is carefully routed is what we should all be striving for. A large Yagi on a rotor would be optimum, but well beyond what most folks require for decent reception. If that's not possible, you may be stuck with one of the indoor antennas or the homebrew that i described. One of the advantages that the design that i mentioned has is that it is vertical rather than horizontal. If you don't think that this makes a difference, take a listen to your car stereo sitting out in front of the house. Chances are, the stock Delco, Ford or Mopar "sound system" with an external body mounted antenna just might be able to pick up stations that your high dollar tuner with great specs and amplified indoor antenna can't seem to pull in. There are two reasons for this. The car antenna and the vertical dipole that i suggest are both omnidirectional whereas many of the amplified antennas and the "T" antennas are cross polarized (both vertical and horizontal) and relatively directional. This means that they are highly susceptible to multi-path and far more sensitive to "aiming". With the vertical dipole, you shouldn't have to fuss with orientation as long as you keep the entire antenna vertical and mount it as i described. If your trying to pick up a specific station but are having a hard time doing it, you can make the vertical dipole somewhat directional by playing with the orientation and direction of the ground (bottom) wire. Another reason that the center fed dipole works well is that the antenna is naturally resonant at the lengths that i mentioned (between 28" and 32"). It therefore offers gain over an "untuned" or "non-resonant" antenna that is of random length or design. One more comment is that sometimes what we attribute to being a poor incoming signal is actually TOO much signal. This can cause front end overload. Signs of this are that the station has a "ragged edge" to it and always sounds like it is not exactly on center channel. While this might sound like the symptoms of a weak or distant station, the difference is that these stations come in quite loud and can be tuned in over a wider frequency range than normal. The signal is so strong that it is actually bleeding over onto adjacent frequencies. This can be caused by being very close to the transmitter or having an amplified antenna system turned up way too much. In some extreme cases, you might even need to install an inline attenuator. This "eats up" some of the signal coming into the tuner, reducing it's strength to a level that the the receiver section can more easily deal with. Keep in mind that if you do have a "mast mounted" amplifier near the antenna, the indoor section of this device MUST be located BEFORE any splitters are put into the system. In other words, you would need to have the outdoor antenna connected to the mast mounted amplifier section, a piece of coax coming down into the house, the control section of the amplifier and then any splitters that were absolutely necessary. Placing a splitter between the mast mounted amp and the control panel could either reduce or absolutely kill the performance of the amplifier, making it useless and sometimes even detrimental to the system. This is often overlooked or not fully understood by inexperienced installers. For those that desire the best performance from their FM systems, you might want to check into the Magnum Dynalabs Signal Sleuth. This acts as both an amplifier and filter and is commonly referred to as a "pre-selector" in the RF field. This makes the signal both stronger and sharper sounding while rejecting outside interference. Hope this helps. Sean >

>