2. analog
  3. 1201630320

Setting antiskate on a Pro-ject arm

I just got back into analog with an entry level Music Hall turntable and am enjoying it tremendously. I recently changed the cartridge to a Shure M97xe which has a significantly lower optimal VTF than the cartridge which it replaced. (1.25g vs 1.70g) I am assuming that I need to reduce the antiskate also. Is this correct? On the pro-ject tonearm there is a little stub near the pivot point with 3 notches. The manual says to place the antiskate weight/thread on the middle notch. Assuming that I'm correct in needing to lower the antiskate, which notch is the lower value - the one closer or further from the pivot point? I figured it's the closer notch but to be honest I listened with the antiskate on all 3 notches and I can't really hear a difference. I don't want to damage my records over the long haul so I thought I should set it right even if I can't hear a difference.
Thanks in advance for your help!
tooter
7 responses Add your response
zeal's avatar
zeal
168 posts
 
The guy who set up my Pro_ject 9 recommended that I didn't use the anti-skating weight at all. When I hooked it up anyway I notice more noise and a boomire bass. Louder music was coming out one speaker then the other when I put the anti skating string all the way to the inner notch. Sounds find without it though I do notice my arm coming down at an angle with or without it on and hanging.
vinylrowe
31 posts
 
Tooter

You are correct that VTF and antiskating should match up.
Easy to verify if you have a Rega table and RB 300 tonearm. Eyes and ears will work best in your case. Pretty sure you will end up on the middle notch which I believe covers the VTF range you mentioned. My Pro_Ject Experience owners manual (which is temporarly M.I.A) listed 3 measurements I.0 1.5 and 2.0 for the notches but the numbers were not in grams rather in some other form of European measurement that I never fully understood. Anyways I'm sure your up and ready by now!!

Cheers
tooter OP
85 posts
 
Thanks vinylrowe, I'll check out the "drift" and try to adjust accordingly. My understanding is that antiskate should be equal or less than the VTF so if that's the case I only have one option.
narrod
1,064 posts
 
Vinylrowe's advice is good and I agree. I don't know the table but, logically, the notch closest to the pivot will provide less tension and, hence, lest anti-skate. However,
I may be wrong.
vinylrowe
31 posts
 
Tooter

Narrods advise is okay. The sure fire way to find out is by placing the arm about half way over the record and then allow the needle to drop onto the record (use the cuing lever). It should drop straight down. If it drifts either way the anti skating is not correct. A little drift back ie 1 mm. is acceptable and desirable. Narrod is correct that innergroove distortion is the final litmus test.

Some have advocated not using the weight at all. You might be able to get away with this but in the long run I am not so sure. Also make sure the table is PERFECTLY level !!
tooter OP
85 posts
 
Thanks Narrod. I'll listen for the innergroove distortion and adjust accordingly. Am I right in assuming the notch closer to the pivot is the lower antiskate setting?
narrod
1,064 posts
 
If you can't hear a difference leave it in the middle notch. You won't damage your records with it in any of the three locations. Listen for innergroove distortion as the arm gets closer to the label. If you don't here any distortion the anti-skate is fine.
Log in to respond
More to discover
80x80
Oracle Audio Technologies Delphi MkIV
80x80
ZYX Ultimate 4D
New Review
80x80
Technics SL-1000RE-S