Audio Research VT100 MK1 and LS15 HELP!!!


I recently bought this set VT100MK1 and preamp LS15 and while I was at this seller house he demonstrated the sound from his online Tidal on TV connect optical to the DAC Luxman DA - 06 then this go to the preamp LS15 and out into the VT100. This set up sounds amazing at his house. However, when I came home play CD from the Sony X1100ES Blu-ray player RCA output into the LS15 and out to the VT100 and it sound horrible - no bass at all in any type of music.  The sound sometime muffle and not clear and most importantly the bass missing tremendously. Im using a pair of KEF R900 Speakers. What is wrong here? can anyone help me correct the sounds? it is because I didn’t have the Luxman DA - 06 DAC? or it is because I don’t have those fancy hundred - thousands of dollars cable?  or the CD source is playin at 41khz /16 bit not high enough signal?  

This is my first system and I don’t know why I can’t get that high fidelity sound from the ARC equipments.  I'm waiting for the Audioengine B1 to arrive so I can stream Spotify into the LS15.   What is wrong with my set up?  Thank you in advance for helping me solve this.
kentrent
If you’re hearing 60% more bass by only switching the amps, then the issue is not speaker/room set up. Assuming the tubes are fine, I would suggest trying to borrow a preamp or an amp from someone and try to isolate the bottleneck systemically. Interconnects, power cords, or speaker cables can affect bass quality but not anywhere close to +/- 60%, in my experience.
Keep at it and good luck.
It sounds like you're at a point where it needs to go in to a repair shop for a diagnosis.  If there's that much difference in sound quality and you've tried all the obvious things, it's time to get it looked at.
Same set up, I switched out the arc and use the mac1500 and has a lot of bass response especially low. Switched back to arc and it has about 60% decreased in bass. All speakers wires are all properly connected. Can someone here explain this?

https://classicreceivers.com/mcintosh-mac-1500

http://sportsbil.com/mcintosh/Receiver/MAC1500/MAC1500_ser.pdf

But what about the LS15 preamp?

You didn’t just switch out the VT100 amp.
You switched out the preamp, amp, and balanced ICs.

Just curious, what do you have the tone controls set at on the MAC receiver? Flat, ( 0 )? How about the loudness button? In, on? Out, off?



You need to find someone to come into your home to help you to resolve your problem.



Firstly, I overlooked your comments about the LS15 going into protection frequently. This could well be the result of the V3 6922 flashing/sparking. If the LS 15 doesn't require re-biasing you can easily change this tube yourself with like kind and quality. ARC is correct, this Sovtek 6922 doesn't flash on turn on. FWIW I don't think this tube needs to be re-biased. Ask ARC.

Re the loss of bass response, as stated earlier, I think it is a fundamental difference between your Mac, an old vintage tubed receiver known for overblown low frequency response, and a modern amp/preamp known for its more linear, cool, and for many, clinical response. The basic difference between the two is huge! I suspect that you have just made a fundamental beginner mistake, and we all make them, of assuming that what we hear elsewhere will be what we hear in our own homes, but to our disappointment it does not. Been there, done that!

 This is especially so when the seller has taken great care to match and set up his audio system. A good audiophile can obtain excellent results from fairly ordinary stuff because of his basic understanding of his stuff,  how it all synergizes, and the requirements of his room for proper set up.

That said, in order to optimize the bass response of your current stuff, I would run your speakers off the 4ohm taps. I would buy a SPL meter and a test disc  and insure that you speakers are not located in a bass null (and at the same time help pin down getting the best overall frequency response). I would also buy Robert Harley's book on audio for a good primer about audio. 

@newbee thanks for your explanation.  But the different is so huge.  It’s like the ARC has no bass at all.  The Mac1500 does have tone control but i flat them just to compare and it still boost a large amount of bass.  I called ARC and they said that tube 6922 doesn’t requires re-baised but that’s not normal for it to sparks.  I called Kef and they said not recommended to use the speakers in 4ohm when the speakers are rated at 8ohms.