I own an ashly parametric model SC-66.It's probable twenty five years old.This thing sold on ebay for 75.00.It is a dual ch. four band.Which means you have two sub bands per ch.You can use it as a notch filter but,never boost.Only cut.If you have a dip in freq. in your room you must try everthing first(moving it all over the room).Until the response is as smooth as you can.Then you cut the bumps(room modes out).Boosting bass freq. in an area in which there is a black hole will over drive your sub driver and ruin the amp or the driver it's self.If you understand the parametric you can widen or narrow the cut,adjust the freq. , and reduce the gain by about 15db.A true notch filter will reduce by 30db.15db is usually enough.Most rooms have two modes in their sub range 20hz-80hz.You could get by with a mono but what the heck the other ch. is alway availible.Eq's on all the ch. will also help.Most modern eq's are quiet and add and subtract what they are suppose to.Ashly is made in my home town and I swear by them.Call the tech guys and they will set you strait.There will always be a fierce difference in opinion when it comes to eq's.Both camps have good points and valid ones.What you must ask youself is what works for you.Careful eq's on all ch. will smooth out room modes along with room treatments.Bass absorbers(pressure absorbers).High freq. absorbers(velocity absorbers) are a must.The room must be "treated " well first to avoid over eqing.Wish you well.
Test gear for room nodes - parametric equalizers
I have recently taken a serious interest in understanding room acoustics and nodes. I have read some great, easily understandable material from www.harman.com, and some from frequent Audiogon poster Rives at rivesaudio.com. I have come to believe that my system has a great deal of untapped potential that may be masked by room nodes, and that use of bass traps, etc, are not answer. The skinny I am getting is that we could all benefit from high resolution room acoustic measurements and the judicious use of parametric eq's to cut the nodes down to size. FYI - my room is rectangular 17 feet by 19 feet, with 9 foot ceilings. Three questions:
1. Does anyone know of a reasonably priced, high resolution room measurement system? Rives Audio sells a system for $600.00, but is that the low end? Can you rent this stuff? After all, you probably only need it for a short while.
2. In a multi-channel system, how few channels of eq can you get away with to tame room modes? I would think perhaps three would work for stereo music(one for subwoofer and two for the main channels since they produce the most bass), or do you really need the center and surrounds eq'd?
3. What about reasonably priced eq's that won't defile a good system? Some high end parametrics run $4000-$5000.00. On the other hand, one well recognized pro-gear manufacturer, Ashly, makes some where you could get 3 channels for about $900.00. Would they be a mistake, introducing noise or something? Meyers Sound makes one for a bit more. Above that, it gets pretty crazy, at least for my budget.
1. Does anyone know of a reasonably priced, high resolution room measurement system? Rives Audio sells a system for $600.00, but is that the low end? Can you rent this stuff? After all, you probably only need it for a short while.
2. In a multi-channel system, how few channels of eq can you get away with to tame room modes? I would think perhaps three would work for stereo music(one for subwoofer and two for the main channels since they produce the most bass), or do you really need the center and surrounds eq'd?
3. What about reasonably priced eq's that won't defile a good system? Some high end parametrics run $4000-$5000.00. On the other hand, one well recognized pro-gear manufacturer, Ashly, makes some where you could get 3 channels for about $900.00. Would they be a mistake, introducing noise or something? Meyers Sound makes one for a bit more. Above that, it gets pretty crazy, at least for my budget.