Help power pair of Infinity Kappa 9's please


Hi all!
I have a pair of Infinity Kappa 9's:
Nominal Impedance: 4 to 6 ohm
Power Rating: 60-340 watts RMS
Efficiency: 102 dB SPL @1 watt, 1 meter
Crossover Frequencies: 80Hz, 800Hz, 4500Hz
Frequency Response: 29Hz-45kHz +/-3dB
Physical Attributes:
1x - SEMIT Supertweeter
1x - EMIT Tweeter
1x - 3" Edgewound Voice Coil Polydome Midrange Driver
1x - 5" Polypropylene/graphite Diaphram Polygraph
2x - 12" Cast Frame , L/C Tuned Woofers
Dimensions: 59.5"H x 21.5"W" x 8"D

My room is 12'x12', I have $2500 budget and would like to play music off my computer. I need amp(s), a preamp, and a DAC i guess (is the DAC necessary at my low of a budget range?). I know my budget is low so I will be shopping for very used/old equipment. If anyone has any experience, suggestions, or words of wisdom, they would be very much so appreciated.
Thanks,
JT
jtiesel2

Showing 4 responses by tomtab

jafant,,, why do you need to know that????    im helping jtiesel2 here trying to find an amp that will work with his kappa 9's.   my equipment is not going to help him
so here is what you do.  odyssey audio.   stratos  stereo amps.   buy two. 20 year warranty.  nobody is going to argue with the sound quality here. jtiesel2, if you are a smart man, and I know you are you would consider this option first.   TWO NEW high quality amps for $2,600 that will work. if you notice the amps are 2 ohm stable

◾$1,375 USD
◾2 x 150 Watts RMS @ 8 Ohms
◾2 Ohm load stable
◾Class A/AB
◾2 - 400,000 Hz frequency range
◾60,000µF memory
◾45 amps current delivery
◾<0.04% THD (not audible)
◾>500 continuous damping factor
◾Input impedance 22K ohms
◾DC offset <1 mV
◾RCA & XLR (bridged) inputs
◾400 VA Plitron transformer
◾Sanken Epitaxial Planar Transistors 2SA1216 & 2SC2922
◾Anti vibration dual thickness PCB
◾Power consumption when idle ±30Watts
◾4 internal fuses 250V/6.3A, 5x20mm, fast blow
◾Additional electrical protection fuse
◾54 lbs weight / 24.5 kg
◾Dimensions: 19 width x 18 deep x 7 height (in) /
48.3 width x 45.7 deep x 17.8 height (cm)
so when the 9's came out in the 80's  what amp back then were used to drive them????    i cannot beleve a speaker was made and there are no amp that can drive them.   and since then many amp's came out with lots of power and able to go into 4 ohm loads and lower.  i cannot imagine amps like a parasound hca 3500  with 500 watts into 4 ohms on the bass and a bryston 4b  on the top would not be able to handle the speaker.  if I had those speakers I would get for under $1,000  a pair of adcom 5500's.  I bet they would do just fine.   I had a pair running my infinity 1b's for 3 years and they dident even break a sweat.  that could be had for $400 each  see them all the time on the bay for that.  $800 total.  if it dosent work out  its only $800 not $2.500.    I'm betting they will work.  just a hunch   





I currently have a Stratos DUAL-MONO on my CLSIIa. This amp works VERY WELL with these. The CLSIIa will drop below 1 ohm and this amp NEVER breaks a sweat! Very open sounding and I agree, a little dark.

taken from a post here