Cube Audio Nenuphar Single Driver Speaker (10 inch) TQWT Enclosure


Cube Audio (Poland) designs single drivers and single driver speakers. 

Principals are Grzegorz Rulka and Marek Kostrzyński.

Link to the Cube Audio Nenuphar (with F10 Neo driver) speaker page: 

https://www.cubeaudio.eu/cube-audio-nenuphar

Link to 6Moons review by Srajan Ebaen (August 2018):

https://6moons.com/audioreview_articles/cubeaudio2/

----------------------------------------

Parameters (from Cube Audio):

Power: 40 W

Efficiency: 92 dB

Frequency response: 30Hz - 18kHz ( 6db)*

Dimensions: 30 x 50 x 105 cm

Weight: 40 Kg


* Frequency response may vary and depends on room size and accompanying electronic equipment.
david_ten
It's a rainy morning here in Wisconsin so I thought I'd write some about my Nenuphar journey. Two or three years ago I decided to build a system around high efficiency speakers in order to see what people were talking about. I ended up with the Teresonic Magus monitors and the LTA Z10 integrated amp. A nice combination.

Then at AXPONA last year (seems like a very long time ago) there were two rooms that made big impressions. One was a Goldmund system where notes just hung in the air. However, it ran well into six figures. :-(

The other room featured Nenuphar speakers by Cube Audio. The music was liquid and (to steal a line from Joni Mitchell) stuck to all my senses. So, earlier this year I finally put in an order for a pair of Nenuphar monitors. I decided on the baby Nens, the Mini Monitors. Jon at Refined Audio had one pair in stock.

Although they have the 8" drivers and are only 10" x 14" x 24" high they proved plenty loud enough for my 20' x 14' living room. Not that I listen at head-banger levels. The supplied stands put them a little high for me (I tend to sit low) so they ended up on maple butcher blocks topped with IsoAcoutics Apertas.

To be continued....
charles1dad & others
According to Vinnie's email below the resistor changed the output impedance of the amp to 1 ohm and did not change the speakers' impedance.  Since the stated output impedance of the L2iSE is 0.1ohm the resistor increased the output impedance by 10 times (about the limit of my math skills).  After adding the resistor I did not notice having to increase volume levels, for what's that worth.  Except that it sounded much better at low volumes, as mentioned before. 

Hi Steve,
Glad it worked!
Can you fix a typo?  It should say 1-ohm resistor (not 100 ohm)
And I meant to say that your damping factor is now 8 (not 80) - sorry!
Speaker impedance / amp output impedance = damping factor.  So 8 ohm / 1 ohm = 8 Enjoy it, and thanks for sharing it!
Vinnie

I think the focus on DF is going overboard - circuit is more important. @213Cobra recently told me he believes the Ampzilla 2000, 2nd Edition is the best SS amp he’s heard on Zu Audio speakers which have similar driver characteristics to the Cubes. I was very surprised to hear this (and between him and I, we’ve owned/heard the SIT-1, 2, and 3, and 20+ other P/P and SET amps on them). My personal favorite amp on Zu is Quad ii Jubilees - which also use some negative feedback. I wouldn’t get too tripped up on DF being the decisive factor. Also, Srajan listens at 60db volume levels which is very unusual. For contrast, I want to hear the Tron (reboot by Daft Punk) soundtrack at 90dbs to test amp flexibility.

As far as trying the Nenuphar myself, I reached out to Jon and he was hoping to have stock at the end of the month. There are no places in SoCal to hear them, but he offers a generous 60-day return policy. I’m also looking into the Boenicke which I am hoping to demo soon.

I’m also looking into the Boenicke which I am hoping to demo soon. 

Well, you can't go wrong there. My other speakers (in my music room) were a pair of Boenicke W5se. I liked them well enough to upgrade to the W8se. Different styles but both provide a lot of quality and enjoyment. You may have a hard choice.

- Robert