Anti-Skate Weight …. Better sound without it?


Hello,

I have a Music Hall 9.1 turntable, and I recently changed my cartridge to an Audio Technica AT160ML, moving magnet. It sounds lovely! 

 

BUT… it seems to sound better when I take my anti skate weight off my turn table arm. 

 

One record in particular seems to have Left channel distortion with a female vocal, but when I take the weight off, it disappears and sounds lovely. 

 

It all seems to sound slightly better and more resolved, open, without the weight. 

The needle requires a very light 1 gram tracking weight. I have aligned it correctly, and the turn table is level. 

 

Any suggestions? Is there something incorrect with my turntable setup? Could it be this one record, as i do not notice left speaker distortion otherwise… (i think)… 

 

Or does the removal of the anti skate weight make sense when the needle has a very light tracking force?

 

thanks!

Richard

whyrichard

Thank you @elliottbnewcombjr for the very detailed write-up and shopping list.

I recently pulled my turntable (Thorens TD-320 MkI) from storage where it sat the last 30 years. Vinyl is no longer my primary source, but I enjoy playing the few hundred LPs I still own and my turntable might as well be set up correctly.

Bill, for me, when I did experiment with vs without a dust cover, on some TT that I no longer own and the name of which I can no longer remember, there were very obvious sonic negatives associated with use of the dust cover.  Plus, using the cover is an added bit of fuss for what is already a fussy process (playing a record).  Anyway, since that long ago experiment, I have been a no dust cover guy. I do now recognize that there may be ways to use a cover that do not cause resonance or reverberation to color the sound.  Mijostyn used to discuss this. To each his own, as you say.

Bill

Sorry, my stubbornness is not meant in the way you are taking it. I have no delusions, I have great respect for you, lewm, and many others here, I make a fair amount of errors as you know ... but

I strongly encourage others to take control, not be controlled, or 'out of control', be able to do this for themselves, it's neither expensive or hard once you decide to try. 

Fact: Level; Overhang; 2 Null Points; VTA; Azimuth; Tracking Force; Anti-Skate: that's it, the seemingly scary list is not that long!

I came up with a short list of tools, methods, and easily heard L/C/R imaging content anyone can acquire. Tools, Measurements, Ears.

Fact: Inward Skate is real, directly related to tracking force, and AS, the last thing, must happen somehow. Pure Physics

OP's Tonearm incorporates control of and instructions for AS, but only for the cartridge they supply. OP changed his cartridge. The manual does not help.

https://cdn.shopify.com/s/files/1/0710/4649/6578/files/mmf-9.3finalmanual.pdf?v=1677776693

Fact: Evidence reveals MOST are not getting it right! I've read it, and personally repeatedly confirmed it with VAS, highly regarded re-tippers. That is terrible, we have to admit, the industry has not developed consistently accurate methods.

Fact: Thus OEM Dials and Scales are proven to be NOT accurate; alternate tools and methods are readily available and inexpensive.

 

.....................................

IF, after all else is 'right', very little AS is needed, or even none, that means that AS is already occurring from bearing friction, wire 'pushback', a combo of forces like lewm describes, and you are saying is very often the case.

 the blank side LP method will show only a speck or nothing is needed, AND, use your ears: when listening to the 3 guitarists, very slight adjustments will alter the L/C/R imaging, no drums, horns, voices, no golden ears required, just 3 guitars

especially in the case of light tracking, in this case OP has chosen the lightest of the range given for his wonderful AT160ML cartridge of 1.0g, and as lewm pointed out, we don't know how much AS his dangling weight was giving.

The manual is specifically written for a Goldring Eroica LX which they tell you to use 1.75g tracking force (between numbers 17 and 18), and set the AS weight line in notch #2 (presumably notch 2 is -1.75g AS?). They do not tell you what the other notches represent. (SME tells you each notch is 0.25g I think I remember).

The blank side LP method and experimentation with various notches can get you close, and final refinement by ear

................................

OP can ASSUME everything else is ok, I would rather he KNOW it.

lewm

'Pet Peeve' about Dust Covers I accept, obsession seems unfair. 

Like you, I remove my dust cover during play, advise others to remove them, my peeve is that the majority of the time these fanciful and expensive creations with high precision parts are off, and leaving them out to airborne contaminants is unwise, selling them without a dust cover seems irresponsible to me.

Bearings wear, that takes a long time, but they are effected by airborne contaminants to large or small accumulating degree, and evidence of lack of need for AS reveals both.

 

devinplombier

thank god for people like you, my imagined beneficiary!

 let us know how it goes!

let me know if you find alternate tools, other methods, any way I was unclear, I tried to be concise, keep it simple, I can always edit it.