Who knows something about Tri-channel 3-channel stereo for music (not HT)?


I happen to have 3 Martin Logan 'Source' e-stats, and want to overcome one of my main complaints with these speakers... narrow sweet-spot.

Having heard of 3-channel stereo, had the idea that instead of using a stereo pair, I might incorporate all three to solve several issues (narrow sweet-spot and low impedance), while improving 3-dimensional holographic imaging for added benefit.

I know there was an era (before my time and before surround sound), when this was (considered by some) the pinnacle of hifi. I found this article on Magnepan site that details some history on the subject https://www.magnepan.com/betterthanstereo

I have tried connecting the 3rd speaker located in the center in series with the stereo pair - jumpered to positive speaker pole of one (say left) and negative to the other (say right) speaker. In this configuration, I'm not sure what signal is going to the 3rd (center) speaker, but it doesn't follow either left or right, and switching pos/neg connection to the other two doesn't cause a change. So as long as the 3rd speaker is connected pos-pos/neg-neg, it seems to be in-phase and not make either left or right channel dominant.

The effect does increase the sound stage width and impedance (this is a good thing for these low-impedance speakers); however, imaging is no more holographic than is typical for these (and most) electrostats.

So, I wonder what products like the Maggie/Bryston SP-3 and (likely) other similar products of the era offer, that would be an improvement over what I'm doing with series wiring? What about the benefits/pitfalls of various circuits L+R, L-R... etc., and what works best for imaging?

Happen to have some equipment (unused Denon AVR, miniDSP 2x4HD, Emotiva A800) that could potentially be used to try recommended schemes (play) and REW with calibrated mic (to measure results). Currently reconfiguring my 2-channel listening room with two single-stack racks to allow space for the center-channel floor-stander ML Source at center for progression of this endeavour.

Any history lessons on 3-channel stereo (from the good old days) or ideas to try are sincerely appreciated.
128x128mwatsme
I have tried connecting the 3rd speaker located in the center in series with the stereo pair - jumpered to positive speaker pole of one (say left) and negative to the other (say right) speaker
I wouldn't go about it this way, if I understand you correctly the left channel has two 5Ω loads in parallel which means the combined load for that channel is 2.5Ω, depending on your amplifier this might not be a good thing. Also depending on the design of the output stage you're either just sinking the current from the 3rd speaker to ground via the right channel, or worse (if the output is bridged) then you're 'pushing' the drivers with one channel and 'pulling' from the other which is unlikely to sound good. 
I'm afraid I've not come across 3 channel stereo before but I do remember reading that crosstalk between the left and right channel can in some cases appear to widen the sound stage. To emulate that you'd only need a low level signal going to the centre channel. You could also adjust the toe-in of the stereo speakers to widen the sweet spot.
I suggest that you use the minidsp before your main amplifier and use a spare amplifier to power the 3rd speaker. In the software you'll need to mix the left and right channels down to mono for the 3rd output (the input to the mono channel should have the left and right set to -3dB to prevent clipping). This means you can adjust the phase, level and frequency response to both the stereo pair and the 3rd channel.
Hope that's helpful.

Pragmasi,

Thank you for the response! 

The way I've tried already,  puts the center in series with L&R (increasing impedance and causing no left or right bias). It also increases dispersion for wider sweet spot. It fails to increase holographic image.

I like the idea of using miniDSP as you described - think there is merit there! 

I have an 8-channel Emotiva, so all equipment is in place to make it happen. 

It will be fun to play with, and see if I can achieve something close to the LXmini sound I heard last night for the first time - WOW!
puts the center in series with L&R
I think I'd need to see a diagram... I assumed you meant left and right were wired normally with the centre taking a tap off one positive and the other negative. If that was the case then follow the positive wire that's connected to two speakers, each speaker returns to ground putting them in parallel. The only way I can think you'd have them in series is by daisy chaining them from a single channel. Anyway... the miniDSP is the way to go for experimenting.

It will be fun to play with, and see if I can achieve something close to the LXmini sound I heard last night for the first time - WOW!
I've been meaning to build LXminis for a few years but other projects keep getting in the way. The full range speaker in the LXmini is designed to have a cardoid dispersion so I guess it's all sweet spot in front of them. Do you know if the ones you heard used miniDSP or Nelson Pass' active crossovers?