New Tweak --- Its Fantastic


THE NEW TWEAK

Over the good part of this past year I’ve been beta testing a new tweak, the name of which is "Total Contact." Its a hi-bred graphene contact enhancer that is different from all other contact enhancers that have come and gone for one reason or another. I’m not new to these contact enhancers, having had quite a bit of experience with a product developed by the late Brian Kyle and his "Quick Silver" contact enhancer. The "Total Contact" is different ... a LOT different.

"Total Contact" is graphene based and is not a vibration control. It eliminates micro-arching between two contacts. Micro-arching, much like Micro-vibration smears the sound in our stereo systems. Its the type of distortion that we don’t know is there .... until we eliminate it. There is no break-in as we know it. The sound is improved right off the bat, but what you hear is only a smidgen of what’s to come.

I tested three generations of "TC," each of which was an improvement over the previous incarnation. The final mix was cryogenitically treated and made for a more effective, much smoother application. It comes in a large hypodermic needle type plunger containing 1.5 ml of product and includes a instructional DVD and an application brush.

The application should be applied with a very thin coat to all of your electrical connections .... from your cartridge pins to your power cords. I did my entire system, including the ends of my fuses.

Upon initial application, you will notice an improvement in clarity, correctness of tonal balance and a more overall organic sound. But ... that is just scratching the surface of what this magic paste does. As it cures, the improvements become more apparent. Much more!

There are two real break-through events that happen almost to the day with "Total Contact," one at four weeks and another at eight weeks . At four weeks, you’ll get a real jump in clarity and overall improvement. That’s only a taste though of what’s to come at eight weeks. At eight weeks your system’s focus will make a jump in SQ that is so real - its surreal.

After 40 years in the hobby, and a total tweak nut, I have never heard anything that does what this graphene paste does. The see-through clarity at eight weeks becomes simply amazing. The "paste" eventually cures into a kind of polymer plastic and it seems that the sound improves with each listening session. So, its important that you leave your contacts alone for the duration. If you’re the type of person that continually switches wires in and out, you’ll have to re paste until enough time has elapsed to get "the cure."

The only problem I had was with the first batch and that had to do with shorting out a tube pin in the line stage. Use the "TC" very sparingly on tube pins, if at all. I only had problems with the line stage tube pins. The Amp, CD Player and Phono Stage has had no tube pin problems at all.

Tim Mrock, one of our fellow A’goners, is the developer of the product. Its taken Tim 15 years and several patents to get it right. Tim has "pasted" every electrical contact he can find in his audio system, all of the switches in his circuit breaker box, every contact in his car ... and has used it in commercial applications such as hospital circuit breakers, surgical lights ... and other places where efficiency and long life of electrical components are deemed important.

This product is highly recommended to anyone who truly wants to get the most out of his/her audio systems. There’s enough product in each tube to do at least two audio systems as it just takes a very thin coat on each application to be effective. The last tube was enough to do my system twice and then a friend’s system this past weekend.


Frank

PS: There were a couple of other A’goner beta testers of this product as well. Hopefully, they will chime in here with their experiences for comparison. I "pasted" both of Steve Fleschler’s systems a few days ago, perhaps he will comment on his results too. We forgot to paste Steve’s power cords though, so there’s a lot more to be had from Steve’s two fantastic systems.

Frank
128x128oregonpapa
Getting a noticable improvement tonight from my pasting efforts on Sunday.

Also i opened up the mojo and painted the 2 caps and the top of the DAC chip yesterday. I wasnt sure what the Op-amp chip looked like , would have thought it was fairly simple , i stayed clear of the big chip with all the inputs on 4 sides for fear of shorting those...
So, ive had a week off work and ive managed to paste a good deal more of my system.

inside the amp ive done all the tops of the round caps and the top of an R core transistor. I could not find any fuses that i would readily recognise. I didnt do the DACs yet.

opened up my Rel stentor III. This is old school circuit board with lots of space. Painted all the caps on top, fuses, all the larger solder joints and any power connections and connections to the driver as well as the fuse in the IEC and then i painted the flat plate and bolt on the large torroid transformer. Pasted the input RCA and a shorting plug that I put in the unused RCA. finally the pins in the IEC. Then i taped 2 alpha cards to the amp chasis either side of the torroid transformer bolt.

i use a cisco network switch, pasted round caps, IEC and placed an alpha card over the top of the power section of the switch. I grounded the chasis to my power block and pasted that connection.

i have this Russ Andrews passive power conditioner called an ultra purifier, pasted bare wires and solder inside looks like 2 very large caps in there but they and most of the components are covered in a black rubberised plastic so left it there.

ive now done all my power leads plug connections including fuses and my double power outlet at the wall including a good pasting to the inside of the metal casing that houses the socket and an earth connection.

ive also invested in some Townshend speaker bars to isolate my speakers and stands and ive put some stillpoints ultra SS under the sub.

My amp, power bar , switch and apple Tv are all on black ravioli mk 1 pads stacked on to oak cones , additionally the amp sits on a granite chopping board and that sits on a partially inflated wheel barrow inner tube 😉.

ive got to say that the system is sounding very good now , the addition of the townshends and stillpoints and the extra pastings have really taken the soundstage to a different level the details coming out of familiar tracks in some cases is like listening to a remix. The best bit is the tone and musicailty of the system it just feels like its spot on for tone and timing and the soundstage is embracing now its all around the room, not holographic in my case more like a wall of sound with some effects to the side and behind me. I think if i had different speaker cables I would get more holographic sound staging, however I like it as it is anyway. Got to say that sitting inside the soundstage is actually a little wierd at first almost disconcerting , like travel sickness , but now that Im used to it I really love it.

ive got about 70% of my paste left and ive not put any in my consumer unit yet.. i need to get an electrician in to fit a switch between my meter and the consumer unit so that I can work on it.

ive also managed to paste my patch cables i just pasted then removed from the plastic by carefully wiping away.

very happy customer here Tim thanks 🙏🏼 and i know there is more in the tank so to speak. 
A tip for anyone who has an SR active grounding block (should work on the passive block as well). As well as pasting the pins as you normally would, tightly wrap all the HR grounding cable terminations with TA-32 fo.Q tape, then thinly paste the entire outside of the tape with Total Contact. Then paste the copper grounding strip all over. After doing this, the fine grain resolution in your system should be hugely improved. Mine sure is! The effect of doing it this way is multiple times better than just pasting the grounding pins.
Pasting the tape is the essential step. The tape can be removed if you don’t like the effect. Which I simply can’t imagine.