Lamm LP2 Deluxe vs. Manley Steelhead

*** I suppose there is (some?) degradation…

I suppose to you were ably to detect, filter out and interpret those degradation

*** honestly, it's hard to see how much there is given the quality of the phono stage.

What dose it mean? Manley uses low gain tubes and many “toys” inside that forced then to pile-up superfluous amount of active stages. Lamm is two only stages design with a filet inside, that is all that you need to perform the purpose of the RAII correction. This dos not say anything about sound of those units but it at least indicated the initial intentions. Yes, it is nice to have at TT with automatically changing records but…

*** One of the advantages of the Manley is that the loading does, in fact, make a big difference as far as the final sound. You can fine-tune it, as it were.

Yes and no. Those “advantages” are fine sound in the reviews and in the marketing brochures but let look at those “advantages” under the real life. The capacitance loading is fairly funny things. The MC cartages do not really need it. The contemporary MM cartages are not sensitive to capacitance at all. (Actually then need it is as low as possible it means no extra capacitance) Impedance is very different story. However you have all this federal case created just because you need to fine one single resistor value… and forget about it then. Why don’t you fine this value by many other conventional methods and to replaces the default resistor. This little path up to the grid of your first tube is critically important: layout, the type of the resistor, proximity and so on. Those phonostages are not $500 Sony receivers where you comfort is the primary aim. Those multi-thousand dollars phonostages exist not because you are willing to have fun by dialing-in the cartridges loading but to yield a maximum result form you analog insulation. The only one real advantage I can see in the Manley’s loading is ability for the reviews to write this doodles very fast and to move forward to another product.

Rgs,
The Cat

PS: BTW, the discrete values that Manley offers are not narrow enough (from my point of view). However, an average audiophool dose not know how to dial-in the correct input resistance and how to properly damp those MC cartridges. In the best case they run like wounded in the ass antelopes between the voicing their systems by the loading resistor values, “voicing” by the VTA setting, “voicing” by the phonocables, “voicing” by the overhanging and so on. (I’m not kidding: I have seen it a number of times event in context of very expansive installations and in context of people with very high “audio reputation”.) As the result an average audiophool could come up with some kind of more or less “pseudo-balanced all-together sound” but it has nothing to do with a proper cartridge loading. Generally I agree with what Lamm did: The level at which all those “product-type” phonostages perform it is not necessary to arm a “voicing hobbyist” with an extra discrepancy-able-to-induce gismo.

I would like do not comment on Lamm/Steelhead sonic qualities but I would like to point out that the “flexibilities” that you pointed out hav a dark side. (Not to mention all those unnecessary in a serious phonocorrector volume controls, mono switchs, needless extra stages and so on…) Yes, it is "cool" to be able to adjust the input C and R but do not forger then you bringing that 0.2 mV signal over all those switches. Many people after thy have found the correct setting take all these switches out. You would need that “flexibility” once in 3-5 years when you get a new cartridge but you will experience the sonic degradations as the result of those “flexibilities” dally.

Well, Hagtech, let me to do some untypical for the felines barking…

You papers are fine (although I would add a paragraph dedicated to impedance loading in case of a step-up is in presents). However, these papers are mostly worthless for an average hobbyist. An average audiophool recognizes the HF resonances as “a HF extension” or “presents of air”. The 99% of the systems out there (if then are not roll off at 10KHz as most of them do) severally screw harmonic balance of HF and dynamic parameters of HF signal (they are just too sharp). Consequentially, an average audiophool unfortunately care only about how to overwrite (“to fix”) the HF imperfections of his systems by “beneficial” introducing of the “sufficient amount of the HF resonances in cartridges”… and his evidences that HF is in presents (there is a LOT of more to it but I will not go there). “An average Stereophile reader” and “AA’s wisdom sucker” would read carefully your article then turn his playback system on and put a record on his TT. Signal, born in presumably HF capable MC cartridge, and if it was not instantly killed by the upper-mid-frequency distortions in tonearm, (most of the tonearms that I have seen dose it) goes to those funny phono cables that severally crew HF, then goes into a non-properly broken-in phonostage (most of them, even after the years of use, are still raw), then it goes to HF-boosting interconnect cables (designed to impress the audiophools while they conduct their dummy “evaluations by contact” and even more foolish “comparing”), then the poor, already dead, signal goes into a primps staffed with HF destroying audiophile-approved capacitors and with a HF crosstalk at 60db, after thein another “I love you, you love me” Nordost-line interconnect, then the signal dive into a power amplifier where most of the time the HF signal looses even it’s DNK identity, after this the signal reach the final stage of the audio terminations: loudspeaker… where if it was not killed but the resonances and phase distortions in the FH high crossover then it will be defiantly end up in those tweeters. The rest of the HF sounds (that have even no remote resemblance to what initially was born in the MC cartridge) will be lost somewhere in the audiophile-wisdom-approved acoustic treatment…. Did I even mentioned those A/D and D/A devises, phono, line and speaker level “optimizers”, those harmonic recovery devises and so on? So, that “an average Stereophile readers” listens carefully his “sandwich of the signal-screwing-devises” and hear “something” and ask himself: “Why this formulas do not work? Hell with those cartridge-loading resonances because without them it sounds like crap! If it is too bright then I will lower my VTA…if it screamy and “not smooth enough” then I would spay the records with Glad-Grove…” Jim, do you think I too “concentrate my colors”? You wish…