How Should We Clean A New Record?



Have you ever listened to a new record a month or so after you’ve cleaned it with a record cleaning fluid (RCF)? Listen closely: it sounds unexpectedly noisy doesn’t it? Many think so and, for this reason, have stopped using RCF on new records! Others insist that cleaning them with an RCF is an absolute must to remove the offending mold release. And then there are those who have always felt that dry brushing is all that new records require. Amazingly, EVERYONE IS RIGHT! If you are interested in how these seemingly contradicting choices can all be valid, please read on.

CAN YOU HEAR THE SOUND OF MOLD RELEASE?

A new record is covered with a thin layer of mold release, unquestionably a contaminant with a sonic character. However, this sound is subtle, a thin veil that’s mostly unobtrusive. The Teflon or Silicone mold release actually acts as a lubricant that protects the grooves without significantly obscuring the Vinyl’s sound. Countless times I compared the sound of new records BEFORE and SHORTLY AFTER cleaning with an RCF. Without Vinyl lubricant or preserver, the difference is ever so slight and seems barely worth the effort and the risk of using an RCF. Still, a mold release is a contaminant and a dust magnet; it makes sense to remove it if this can be done safely.

THE NOISE OF RECORD CLEANING FLUIDS ON NEW RECORDS

Can an RCF make a new record noisier? The surprising answer is yes! A small fraction of all RCF ingredients ALWAYS remains on the Vinyl surface as an adsorbed film after vacuuming (see my primer on RCF from last week). Held to the Vinyl surface by intermolecular forces, this film is only several molecules thick (less than 10 nanometers) but grooves can also be quite fine at high frequencies (about 100 nm). Amazingly, many can hear the sound of this adsorbed layer!

But here’s the tricky part. The cleaned record is quiet shortly after cleaning as the adsorbed film after vacuuming is still wet—a WET FILM dampens noise. But days or weeks later, with all the liquid gone, the DRY FILM becomes audible. It is a background noise akin to the sound of a dirty record, but much fainter. You may even think that your cleaned record has been re-contaminated with dust. It hasn’t. It’s the sound of dry surfactant. If you re-wet the Vinyl (by rinsing or re-cleaning), the noise goes away only to return when the record is dry again.

An alcohol-based RCF—diluted with water!—leaves a less objectionable sound on a new record because the adsorbed alcohol evaporates completely under vacuum and leaves no dry film behind as long as no surfactant is used. (Note: Dry adsorption film has nothing to do with solid residue from the distilled water making up the RCF.). But even an alcohol-based RCF still leaves a very faint background noise behind; this suggests problems in addition to dry adsorption film but that’s a complicated story for another time.

WHAT ARE YOUR CLEANING OPTIONS WITH A NEW RECORD?

1. Given the current RCF technology, I recommend the Hippocratic approach: first, do no harm. Use a dry brush on your new records, keep them clean, and stay away from RCFs.

2. But if you must wet-clean a new record—because it’s noisy or you find the sound of mold release objectionable—use an alcohol-based RCF (diluted alcohol; little or no surfactant) which leaves behind little or no dry film. The residual background noise is minimal and inaudible in many systems.

3. If you must use a surfactant cleaner, rinse well with low-residue water. Repeated rinsing is necessary as some adsorbed material always remains on the Vinyl after each rinsing by chemical equilibrium. The record will be quiet, wet or dry. Alas, many of you will find this rinsing ritual very tedious.

4. Alternatively, you can use a RCF with lubricant or preserver. It leaves behind an “oily” film that keeps the adsorbed layer “wet” and noise-free. Just remember that you are now replacing mold-release sound with lubricant/preserver sound, even though that is usually an improvement.

5. Some of you like the effectiveness of enzyme-based RCFs. I have not used them much. Their impressive cleaning action (by chemical breakdown of organic contaminants) is certainly attractive but the concomitant breakdown of the plasticizer, also an organic compound, remains a concern.

CONCLUSION

While nearly all agree that old records benefit from a good cleaning with an RCF, there is no consensus or easy solution for cleaning new records. Since I do not find the veil of the mold release very objectionable, I feel that a dry brush is the safest thing to use on a new record—until better RCFs are developed.

One alternative is to use an alcohol-based RCF which is free of other additives. You may also use surfactant-based RCFs but most will leave a faint background noise when dry (days or weeks later). To minimize this problem, rinse several times with water to remove the surfactant film. You may also use an RCF with a lubricant/preserver that keeps the adsorbed layer “wet”, a trade-off between mold-release and lubricant sound. The long-term effect of such additive is still unclear. (Note: To identify the type of RCF you are using, please refer to my last week’s primer on RCF.)

For safer and easier cleaning of new records, we need novel RCFs employing surfactants that are inaudible when dry. This is a difficult but not an impossible demand. RCF manufacturers should look beyond common surfactants (alkylaryl ethoxylates or alkylaryl sulfonates) which belong to an ageing technology. There are exotic surfactants out there that can do the job. Some are (very) expensive but surfactant cost should not be a factor since only a minute amount is ever used in any RCF (typically less than one part in 100, literally pennies per quart of RCF).
justin_time
Justin_time,

I'm one of those quiet readers who have very much enjoyed reading your posts and following the dialog. The time and effort you've contributed to sharing so much good technical information and experience is valued in this corner - THANK YOU.

At the same time, I find myself, based on my experiences over the years as a non-technically trained vinyl enthusiast, very much following the same process and philosophy as Lugnut, Loontoon and Dougdeacon: everything here gets cleaned with one of the commercial fluids, thoroughly rinsed with distilled water and vac'd before the stylus ever touches 'em. Dry brushing with a carbon fiber brush is then mandatory before playing.

Still, your explanations have been most helpful and educational. Thanks once again.

Regards,
Rushton, thank you very much for your words of appreciation.

Your choice to clean all new records with an RCF and then rinse them with distilled water is completely valid. You should have no trouble with the "dry surfactant" noise that I discussed because you get that problem only when you use a surfactant cleaner without rinsing.

I am getting lazy in my old age. I reserve wet-cleaning with RCF and multiple rinsing for the few new records that I really treasure for sonic and/or musical reasons. The rest gets only the dry-brush treatment.

Once again thank you for taking the time to read my thread and for sharing your views.
I was wondering about the water to be used for rinsing. I use RRL products for record cleaning but do not rinse. I was told, and have read that one uses a two step application, the stronger Super Deep Cleaner then the Super Vinyl wash and vacuum. Then play. Though for new records I only use the latter wash. I thought the vacuuming was supposed to remove the residue. I figured that would do it or it would evaporate. However if I were to rinse, what water would be best and where would I get it? Would typical distilled water work or is there something more pure?

Thanks, this has been an interesting discussion with a lot information.....
Letch,

Check in your phone book's yellow pages under Laboratories-testing. Find a lab that is a Certified Laboratory Service. They make their own lab grade water. This water has less than 0.1 ppm total disolved solids and is ideal for a final rinse.

The local lab here is so kind about giving the water away. Since discovering their existence I've shared the news with a small group of other vinyl enthusiasts that also get the water free. I would suggest that you buy a 2 1/2 gallon container of drinking water at the grocery store and after consuming it have it filled with the good stuff. That way you have a lot on hand and don't make a pest out of yourself by stopping by too often.

Expect the lab grade water to bead up on the record like the RRL Super Vinyl Wash although this somewhat depends on the vinyl's composition. I use a cheap foam paint brush to gently work the rinse water into the record surface for a couple of rotations and immediately vaccuum.
A few answers for Letch about rinsing and vacuuming.

YOU WROTE: “I was wondering about the water to be used for rinsing. I use RRL products for record cleaning but do not rinse. I was told, and have read that one uses a two step application, the stronger Super Deep Cleaner then the Super Vinyl wash and vacuum. Then play. Though for new records I only use the latter wash….”

If you use RRL SVW on your records, you do not have to rinse them after cleaning. The point of rinsing is to remove the surfactant left on the vinyl after vacuuming that can be noisy when dry (weeks later). But RRL SVW contains a lubricant (carboglycinate) which will keep the left-over surfactant wet and will also dampen the noise. You can rinse with water if you like, but this action will remove not only most of the surfactant, which is a good thing, but some of the lubricant as well, though not all.

YOU WROTE: “…I thought the vacuuming was supposed to remove the residue. I figured that would do it or it would evaporate...”

Vacuum physically removes the bulk of the fluid from the vinyl surface and evaporates the rest. But some surfactant will stay behind on the vinyl surface by adsorption or simply because it is a heavy liquid or a solid that does not evaporate under vacuum. Surfactants, and other materials dissolved in the RCF will remain on the vinyl after vacuum to make up what we loosely call residue.

Good luck with the water (you may also want to check my response to Lugnut about water source).