kanchi647
Responses from kanchi647
| Best SUT For Van Den Hul Crimson Stradivarius cartridge @bukanona mine is Crimson Stradivarius which has an output of 0.95 mV. At the bottom of the page, it says Stradivarius specs coming... | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge All the comments greatly appreciated.Can you please suggest a good line stage/Pre-amp.Thanks!! | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge @bukanona I could not find any EMT STX 5/10 for sale. Is the EMT STX20 silver coil? It has 10db gain and will be enough gain for the VDH Crimson cartridge. | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge @lewm Yes, I realized that one cannot increase the impedance by connecting resistors in parallel.I have a Ypsilon MC26L SUT for Ikeda Kai cartridge which has 1:26 turns ratio. 57K||26x26= 84ohms. I belive the internal impedance of VDH could be 20-... | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge @lewm thanks for all the explanation.I have read about 10-20 articles detailing all about impedance (47K)/square of turns ratio and how to modify the load using parallel resistors at the out put and in put.If I use 1:10 turns ratio, the cart sees ... | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge Any suggestions for silver SUTs. Are silver that much better than copper? | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge @elliottbnewcombjr what is the difference between Impedance selector and load selector?https://www.ebay.com/itm/KONDO-AUDIO-NOTE-AN-S7P-MC-STEP-UP-TRANSFORMER-JAPAN/123923446228?hash=item...Thanks | |
| Best SUT For Van Den Hul Crimson Stradivarius cartridge @lewm the VPS 100 -> CARY SLP 05 -> CARY CAD 211 FE -> KEF Blade speakers.I did connect the cartridge directly into VPS 100, but had to increae the volume to 100% to get enough sound level.Which is why I am looking for a SUT. | |
| Isolated ground for 20 amp Which kind of Siemens 20 amp breakers do you recommend for dedicated lines. GFCI or regular? standard trip or arc fault?I have 2 x 200 amp panels. Each panel has two columns of breakers and from what I gather, alternate rows are same phase. | |
| Hum with Ypsilon MC26L SUT that goes away with touching @bukanona the tonearm cable is a silver IC with WBT Nextgen Silver RCA from Reed 3p.the stage 3 connect cable is connecting SUT to Phonostage VPS100. | |
| Hum with Ypsilon MC26L SUT that goes away with touching @dover how do I connect one end to true ground? | |
| Hum with Ypsilon MC26L SUT that goes away with touching @dover the whole concept of stage 3 cables is air-dielectric which is supposed to have the least capacitance (air has the least dielectric).. | |
| Hum with Ypsilon MC26L SUT that goes away with touching The stage 3 has an extra cable hanging out with spades on either end to connect to the ground post.my DIY has two wires- center one is conductor and the return is helix.. | |
| Hum with Ypsilon MC26L SUT that goes away with touching @lewm my home made IC doesn’t have a sheild or ground conductor. Neither does the IC made by Ypsilon. The Stage 3 concepts IC has a ground conductor and I tried multiple configurations which had hum- including connecting only one side, both sides,... | |
| Hum with Ypsilon MC26L SUT that goes away with touching Update:the hum disappeared after I replaced the Stage 3 concepts analord interconnect from SUT to Ypsilon VPS100 with Ypsilon interconnect.i also made my own IC using helix design from http://www.image99.net/blog/files/category-002a002a-the-helix... |