mke246
Responses from mke246
| MC-MM-MI CARTRIDGES . DO YOU KNOW WHICH HAS BETTER QUALITY PERFORMANCE? REALLY? Raul, I know it’s been a lightning rod in the past and my particular usage case is rather unique to say the least, but I’ve spent the last several months carefully comparing a Soundsmith Strain Gauge with several custom truncated elliptical stylii... | |
| Do you think you need a subwoofer? Got the Genelec 7360As integrated into my system just now. With GLM adjustments they're pretty good for my needs, especially mono stuff where the minor deficiencies in one channel offset the other. I'm sure I could improve it a bit if I adjusted p... | |
| Do you think you need a subwoofer? After doing some research the past couple nights I'm strongly considering adding a pair of Genelec 7360s to complement my 8351Bs. I know Genelec recommends the 7370s, but I think the 109 dB SPL of the 7360s is more than enough for my needs (even 8... | |
| Do you think you need a subwoofer? Genelec recommends 7370A subwoofers (around $4k each) for the 8351B but also has said in the past that 7360As (around $2.5k each) are fine if your room is on the smaller side and you listen at lower-to-moderate SPLs, which would fit my situation. ... | |
| Do you think you need a subwoofer? Most collectors playing 78s are not going to hear the full potential of the records because their equipment is the equivalent of playing an LP on a Crosley. Bad stylus fit, bad EQ, suboptimal processing capabilities, or simply not playing an archi... | |
| Do you think you need a subwoofer? Good points, I may think about getting a pair of Genelec 7360s in the distant future. Not something I really need but might be fun to have. I mostly work on ancient acoustical and early electrical recordings from the 1910s through 1933 or so, and ... | |
| Do you think you need a subwoofer? I'm happy with my Genelec 8351Bs that reproduce accurately down to 32 Hz with no subwoofer. Most of what I listen to, i.e. recordings of acoustical instruments and ancient 78 RPM records, isn't recorded below that, anyway, so I don't care. It woul... | |
| Should I update a vintage 16" broadcast transcription turntable? For that price or not much more you can get an older Technics SP-10 with something like a SME 3012 tonearm (12") on a cheaper plinth and have much better performance. You only need a ~10" tonearm to play transcriptions, so you could even mod one o... | |
| Turntable prices. Is my mind going? While I generally understand the ultra-high-end market, I can't help but roll my eyes at six-figure turntables that don't even spin at 78 RPM and have the exact same measurements as the $10k Technics SP-10R, $20k if you count the plinth and equiva... | |
| US source of Panzerholtz? Yes, I had Precision Composite Industries make me a custom replacement Albert Porter panzerholz armboard and am very happy with it. I toyed around with the idea of commissioning a new dual-armed Albert Porter style Technics SP-10 series plinth, bu... | |
| Tonearms for reference 78 RPM system Technics SP-10R Still loving my Fidelity Research FR-66S, but my alternative setup with a Dynavector DV-505 is also producing great results. 78s often have high-speed warps, and the Dynavector seems to track them very smoothly, picking up a lot less distortion th... | |
| Working with 78’s It depends what era of discs with which you're dealing. Most 40s and 50s 78s were cut with a 2.5 mil groove, but earlier discs are all over the place. Archiving 78s is an extremely complex topic, and there are reams of information out there. ... | |
| Turntables: 2 Tonearms. What do you Have or Know About? My setup for 78 RPM audio restoration: Technics SP-10R in Albert Porter panzerholz plinth Primary arm: Fidelity Research FR-66S direct-wired with Shure V15 Vx and dozens of custom Expert Stylus stylii with various truncated elliptical and conic... | |
| Connect 78 rpm turntable to Vinnie Rossi L2i SE amp? With 78s, the biggest factor is stylus size. You need a 2.5 or 3 mil stylus. There are a lot of options, but the easiest off-the-shelf solution these days is this: https://www.audio-technica.com/en-us/at-vm95sp Dual turntables are OK, but I w... | |
| Discuss The Viv Lab Rigid Arm I put my 9" HA arm up for sale a few easy-to-find places if anyone is interested. I’m still somewhat agnostic as to the discussion surrounding the fine details. Kind of tempting to try to put the arm to the test, but I’m mostly a 78 collector. Alt... |