imhififan
Responses from imhififan
| Need Adcom GFA-565se info On page 9 of the user manual:All loudspeaker systems having a nominal impedance down to 2 ohms can be connected to, and driven by, the GFA-565SE. The GFA-565SE can drive these low impedances at more than adequate power levels with no difficulty. l... | |
| Can This Amp Power A 50 Foot Speaker Cable Run? I ’m with zavato, the cable should be ok, most important thing to consider is the amp has enough power for such a big theater room without clipping and destroy the speakers! http://myhometheater.homestead.com/splcalculator.html | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- Tim, my guess is a combination of difference of ESR and those old electrolytic caps dried out and out of specs, so a tester that can check the value of the caps and ESR will give us the answer.One thing that surprised me was the cables made such... | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- Btw, all cap in the crossover should be bipolar/non-polarized, therefore the two 2200uf connected back to back. | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- Yes, C1,3 and 4 must use bipolar cap | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- The two 2200uF polarized electrolytic back to back in series to form a non-polarize cap. | |
| Toshiba SP-690 http://audiokarma.org/forums/index.php?threads/vintage-toshiba-ic-boston-system.326512/ | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- I think what Ill do is buy a tester that can check the value of the caps as well as check the ESR and see what pops out at me. Totally agree, and this link is worth a read:http://www.diyaudio.com/forums/multi-way/282847-original-electrolytic-ca... | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- The caps I replaced were: the electrolytic, (2- 6.8uF , 2- 8uF, a 47uf and a 10uF) Also film caps, 3- 3.3uF, 2 -10uF and a 4.7uF.Two polarized electrolytic 2200uF, but these I replaced with electrolytics. C8=4X3.3uF=13.2uF and you replaced it wi... | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- If caps are parallel, measure it in circuit. | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- Just read the caps itself, you can compare the new caps with the existing caps which you took out from the crossover board. | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- How can I tell what the resistance should be, that device that Tim posted , will that tell me the correct resistance? If I measure the other crossover that I haven't changed any electrolytic caps out of yet. If I find out the correct resistanc... | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- With using just plain old zip cord I get better highs than the temporal continuums. Anyone have any idea why? What setting on the dials? on the highest? | |
| HELP AFTER MY MODS, My tweeters are subdued and weak- I did replace two of three of the mid-range caps, as well as three of the five tweeter caps. Can you let us know which caps you replaced? the value of the caps ( ie: 2.2uF 100V)? | |
| Vintage HK protect mode? pizzigri, http://audiokarma.org/forums/index.php?threads/citation-22-in-protect-mode.325835/schematics: http://akdatabase.org/AKview/albums/userpics/10004/Harman%20Kardon%20Citation%2022%20Schematic.pdf |