back to ask again long sorry


If you recognize the user-ID, then you know the problem I'm about to describe because I've been yapping about it in these forums, on and off, for *years*. I'm only in here to try again because everything I've done so far to try to fix it has resulted in just more credit-card bills.

The sound is perfect for the first twenty or thirty minutes -- always has been, and I always think I've fixed whatever's wrong -- and then, gradually, the sound becomes reedy and increasingly sibilant in the upper midrange and apparently "over-modulated" right around the midrange-tweeter crossover.

If I shut everything off and reconnect everything, the problem often goes away for another twenty or thirty minutes, but not always.

It can't be a problem with components or speakers because everything in the chain has been repeatedly replaced, and many configurations have been sent off for service and returned with clean bills of health.

I don't think it's RF pollution because I've encountered the problem at a friend's house, and fixed it doing the same thing, over there: reconnected everything and had great sound for... twenty minutes.

I don't think it's a cracked RCA input socket because the problem has spanned several configurations of equipment.

I don't think it's a bad interconnect because the problem has spanned several configurations of cabling.

I don't think I'm delusional because non-audiophile listeners have commented on both the unpleasantness of the sound before reconnection, and the improvement afterward.

At all events, something seems to be "building up" in the signal path, somewhere, and the act of severing all the connections seems to cause whatever that build-up is, to be dissipated.

Lately I've been trying to fix this by... well... *reading* -- about everything from PS-Audio Humbusters to Audience Adept Response power conditioners and back to the XDC power filters by Channel Islands Audio. Trouble is, I'm cleaned-out financially and I just really don't feel like spending any more money before knowing with a bit more certainty that more dollars spent will point me more definitively toward getting to the bottom of this. Are there professionals who can help to diagnose the problem, and who are then also knowledgeable enough about the industry to recommend the proper fix?

Current system configuration: (many, many others have been tried!)

McCormack MAP-1 and DNA-HT5, connected directly to dedicated AC circuit via Signal Cable power cords

Arcam FMJ-CD23 connected directly to nearby, undedicated AC circuit, via signal cable digital power cord

Sony BDP-S550 blu-ray player and Panasonic TX50 plasma TV, connected to APC H-15 power supply, which is in turn connected to the undedicated AC circuit via Harmony power cord

Salk Songtower QWT speakers, front L and R, Linn Trikan center channel, Totem Mite-T rear L and R.

signal cable interconnects, element cable cross-connected speaker cables.

Thanks again, everybody.

Dave O'Gorman
Gainesville, Florida
dog_or_man
Al's last point is a good one and begs more backstory: I've been eating components *and* speakers during all of this, at a rate that doesn't otherwise make sense. The whole trouble started most of three years ago with some Parasound gear that would develop a "whooshing" sound in one channel, almost like when one of your ears is full of water, that could be dissipated by wiggling the IC between the pre- and power amp.

Is that the exact-same problem I'm having now? No, of course not -- but the person from AA with whom I spoke on the phone suggested that, if the mains had an insufficient earth ground, and/or significant DC offset, these problems would compromise the components' ability to deal with the cr*p that was being handed to them from elsewhere in the signal path, like RF or digital noise, and could even lead to damage.

I've eaten a left-channel tweeter in one expensive pair of speakers, a left-channel midrange in another (using different amplification), and sent three different amp/preamp combos away for service, with varying conclusions coming back from the manufacturers. As often as not, even noticeably audible problems with the electronics have not been repeatable on the bench -- which would further suggest something having to do with power, no?
Dog_or_man,
At what level would you say you listen to music on your system? Moderate, above moderate or loud?
I tried some Signal cables a while back and thought they made my system sound like the way you are describing. I tried a Harmonic technology AC-11 power cord and the system sounded much smoother. Also, the Salk speakers are very revealing and detailed. Many of the Cd's you listen to may sound bright in this system. I would throw some tubes in the signal path if I was you. A lot of good suggestions; especially by Almarg. Doesn't cost anything to verify his suggestions. If you can't figure it out, ask for some help in your area.
Hi Dave,

I have seen this problem before in other amps and preamplifiers. What you have is a capacitor or resistor in the power supply of the amplifier or pre amplifier that is changing value. If I were a gambling man I would bet that you have a resistor in one of the power supplies that is in the process of failing or that the resistor is changing its value due to heat. If you are experienced with a fluke and know how to read resistance bands, you could check the resistance values before powering up your equipment and then check the values after an hour to determine what values have changed and are out of specification.