I have worked with most circuit breakers over the years starting with my Dad 55 years ago. He told me back in the day that Square D would never let anyone down. I can add Siemens as another. When adding new panels for audio make sure to specify annealed HC copper busbar materials, not brass or Cuponal. Square D (Schneider Electric) and Siemens both supply them. Be sure to treat the busbars with a copper preservative to slow down oxidation. This is especially important in humid climates. A very good one is Thomas and Betts CP8-TB containing colloidal copper.
Your One Bullet Point Solution; Electrical Upgrade
Two points; I am well aware of many threads on topic of electrical service. I do not have time to read hundreds of posts, but wish to distill them down with your help. I will also post this on the Tech Forum to get wider response:
Doing service upgrade to 100A. I plan on adding a whole house surge protector, type 2, add on to panel after the service enters house. Panel to the HT/Music room is not under consideration, as it was all updated when the room was built.
If anyone has important info/contradictory info on that plan, please inform.
What I would like to know in shorthand form from the community from those who have Done upgrades:
1. Recommended Panel? Brand, any difference?
2. I currently have sub-panel for HT/Audio room which I’m tempted to keep. I understand that this is a good move.
Electrician can sum all into a larger panel, but I have reservations. Comments/recommendations?
3. Particular wiring/breakers for panel/sub-panel for audio use?
4. Particular surge protector recommend.
As the topic has been covered much, notation form comments are welcome. Thanks for helping!
Doing service upgrade to 100A. I plan on adding a whole house surge protector, type 2, add on to panel after the service enters house. Panel to the HT/Music room is not under consideration, as it was all updated when the room was built.
If anyone has important info/contradictory info on that plan, please inform.
What I would like to know in shorthand form from the community from those who have Done upgrades:
1. Recommended Panel? Brand, any difference?
2. I currently have sub-panel for HT/Audio room which I’m tempted to keep. I understand that this is a good move.
Electrician can sum all into a larger panel, but I have reservations. Comments/recommendations?
3. Particular wiring/breakers for panel/sub-panel for audio use?
4. Particular surge protector recommend.
As the topic has been covered much, notation form comments are welcome. Thanks for helping!
- ...
- 53 posts total
Some important details I do not know- Is this a smaller townhouse with gas heat, stove, water heater and no a/c needs? I may not be following your goal here. A new panel under 200 amps is considered an oddity in the markets I have lived in. Unless you fit the parameters I stated earlier and have very limited a/c power needs. Normal procedure when installing an service upgrade is to eliminate sub panels. Have you run your thoughts by a good electrician yet? . You have some of the plan down. Run 2 dedicated 20 amp circuits to your component location. 12 gauge wire is fine. No j-boxes along the way. One circuit for audio and one for video. Use the same bar in the panel for both new lines and do not put it on the same bar with a/c or refrigerator. Buy better grade receptacles for inside the home. Offer at least 4 plugs-ins per 20 amp circuit. Consider this whole house protection Surge/Filtration/Waveform Correction item-Environmental Potentials EP-2050 Bigearstereo.com $900? Grounding is very important. A 10' 1/2" solid copper rod is $13 at Home Despot. Ask your electrician to test the existing one to see how effective it is. One thing not in your control: -Distance to the nearest transformer? Things that screw up sound reproduction: Noisy florescent lights, rheostatically controlled fixtures. Noisy HVAC systems, Noisy refrigerators. You probably knew all this but clarity counts. Good luck with the new service! |
| Post removed |
- 53 posts total