XLR and DBS (Audioquest)


What are your opinions regarding using DBS with an XLR cable? I am thinking of acquiring a set, but am unsure if it really makes a difference.
gdnrbob
I have aq wel w DBS speaker cables and they are fantastic.  I would like to see what happens if I disconnect the DBS however...
Bob, for Atmasphere's comments about insensitivity to XLR cable differences to be applicable, the components being connected, especially the component which is driving the cable, have to meet certain criteria he has described.  His designs meet those criteria, as do some others, but my impression is that the majority of designs that are out there do not.

For his description of those criteria, and for what I consider to be a persuasive proof of his contention, see the first of his posts dated 3-22-2013  in this thread.  Also see my follow-up question later in the thread, and his answer.

Best regards,
-- Al
 
Maybe it would be helpful to pass along my experience on the question of XLR vs RCA. Firstly if you have a long (say >3M) run then you have no alternative but XLR, as RCA will be too probe to pick up noise. Having said that a poor implementation of balanced circuitry (on which Ralph has expounded at length) will sound worse than any single ended. Be aware that many (if not most) so called balanced circuits are simply front or back ends to single ended circuitry inside the amp or component. Hence my recent experience with my DCS kit actually sounding better single ended, most likely as the balanced connection is going through another step to convert single ended to balanced

However in balanced cables favor the XLR connection technology is way better than RCA, no risk of loose connections or bad grounds -- which even led to me losing a woofer in a pair of Magico V3s once

So what does this boil down to? My rule of thumb logic tree

1) Is your connection >3M then, go balanced
2) Is your equipment (at both ends) true balanced circuitry, then go balanced
3) If 1 and 2 are false then go single ended
4) If 1 is true and 2 is false then move your equipment!

Not too complicated in the end 🤔
When I posted this thread, I was doing so with Ralph at Atma-Sphere's belief that XLR cables don't need to be expensive, as they are not affected by distance- unlike RCA.
I guess I'll just have to experiment.
Thanks for all the replies.
B
I have a pair of AQ. Earth interconnects with DBS and XLR termination. All I can say is these cables sound pretty darn good in my system although I can't attest it to the XLR termination. I tried a comparison a few years back with Purist Audio Museaus, both XLR and RCA terminated. one pair each. My CD player/DAC had connections for both so I could rapidly switch between the two to listen to the same cut. I really couldn't tell any difference between the two. Maybe my system just wasn't up to task. I could see where some would think the XLR would sound better because in my comparison, the XLR connection was a tiny bit louder than the RCA connection. To people who are not aware of this, the XLR could be perceived as the better sounding cable. being a   bit louder could be heard as "more resolution." But we all know that wouldn't be the case...
They are worth it and lower the noise floor.  The end result is similar to what @folkfreak mentioned.  However, I'd try them in your own personal system if you can. System synergy and subjective preferences come to play.  As with a controversial cable topic like this you can be sure the pessimistic will also chime in as they already have. 
DBS is an absolute must on the AudioQuest cable line, irrespective of how you have the cable terminated. The effect of engaging the DBS is quite obvious however you will only notice this if you switch it off (i.e. unplug the small DBS jack) as it can take 48-72 hours for the field to fully form. Without the DBS my AQ WEL cables sound rather edgy and thin, with the DBS working fully there is palpable solidity to the image and uniformity across the frequency range. I own both RCA and XLR terminated WEL -- which of the two is better will depend on the equipment used (I just discovered that the balanced outputs on my DCS stack actually sound worse than the single ended so am switching to RCA in that application). Finally AQ will reterminate any of their cables (at cost) should your needs ever change