What is you tonearm’s Maximum Distortion?

I’ve been playing around with different cartridge mounting, as a Grace arm the plinth of my Lenco cannot be mounted at the recommended pivot-to-spindle distance of 222mm (closest it can get is 225mm).

My best figures in theory seem to be:
Max. Tracking Error: 3.51 degrees
Max. Distortion: 1.21 %
Average RMS Distortion: 0.73 %

This is with: P-t-s 225mm; overhang 11mm; offset angle 19 degrees.

• ...
•  42 posts total

I do not get the calculator to work.

I enter in effective length 233.7, overhang 17.2 and offset angle 22.953° with Löfgren B.

And in the calculations and table it spits out today different offset angle  and overhang than I have entered.

I think that the calculator is totally worthless when it spits out data that is not my offset angle  and overhang. (And it doesn't calculate with the provided indata)

So those that got some output did you look that the indata were used is intact or were there their own made up values from the calculator itself!

Or am I missing something here?

@optimize   in order to enter your desired overhang and offset you need to tick the "custom" option or the program will calculate for the 'standard' alignment ticked.

Also the number you enter into the initial arm length will autofill to the remaining three so make sure the same P2S / EL dot is ticked for all 4.

For your calculation enter 233.7 in Arm 1 Arm Length and tick the effective length dot for all 4 arms.  Then Click the Arm 1 custom dot and enter your desired overhang and offset angles and the results will compare 'your alignment' to the big three.

dave

 Parameter Custom Lofgren A Lofgren B Stevenson pivot to spindle (mm) 216.5 215.96 215.45 218.02 effective length (mm) 233.7 233.7 233.7 233.7 overhang (mm) 17.2 17.74 18.25 15.68 offset angle ° 22.95 23.57 23.57 22.35 linear offset (mm) 91.14 93.44 93.44 88.87 inner groove (mm) 60.33 60.33 60.33 60.33 outer groove (mm) 146.05 146.05 146.05 146.05 inner null point (mm) 67.42 66 70.29 60.33 outer null point (mm) 114.86 120.89 116.6 117.42 maximum error ° 2.25 1.85 2.06 2.24 maximum distortion % 0.77 0.64 1.03 0.77 average rms distortion % 0.38 0.42 0.37 0.5

Thanks @intactaudio !

Here is my numbers seams they are pretty good compared to the other's. Using the Löfgren B that is the best on the average for a whole LP.

I did my custom protractor several years ago and it seems to be OK and the numbers I took from that custom protractor.

So I did this also to check its old calculations. 👍🥳

@intactaudio : It’s only a parameter manipulation and that is the SAT tonearms alignment. At the end is not rocket science. Btw, Did you already test that kind of alignment?, I do and you can be " surprised " by.

As Mark SAT designer says and makes sense:  " The null points for the SAT arms are located at 80 and 126mm. Ultimately, this was a choice of enjoying a consistently higher level of fidelity for 95% of the time over having less angular error on 5% of the tracks. "

Exist rules but to each one of us can be broken in favor of quality performance with MUSIC.

That alignmnet by SAT is wrong? no it’s only different and when tested each one of us can decide about. What you think or what I think is only that " think " as is non-important in the whole alignment game: it’s each one game not yours not mine.

R.

It’s only a parameter manipulation

Only a parameter manipulation??? If the parameter manipulation is kept hidden then there is another term for it.

dave

•  42 posts total