upgrading VPI turntable

Power Cord? What will a power cord do to increase performance on a HW-19 Table? Nada. SDS, yes, A SAMA, yes, a better Tonearm, Yes, Better Cartridge, Yes, Better Feet, Yes.

Don't be so sure, that a HW-19 modded to the hilt cannot stay alongside, and compete with a Scout, or even a Classic. The consist of parts, and how they are implemented will go far to play an influence as to the final sound.

A full blown HW-19 MK-IV Table, if VPI was still making it, would probably cost you north of $3,000 in today's market. That was probably one of the main reasons they discontinued it, too much work-labor-parts involved, and work-parts equates to $$$ spent.

All company's business models today are spend less, and make more, maximize profit, that's the bottom line.

You just perhaps recently missed on a nice MK-IV 16 lb Platter that was advertised here for literal Peanuts. One of the best Platters IMO that VPI ever made.

Making a new Plinth for the HW-19 to use another Tonearm is not that hard to do. Nor is having a welding shop cut you out a thick sheet of Steel as a sub-chassis sheet under the Plinth. 10 minutes with a template design, and a plasma cutter is all.

There's a million footers out there that will better the 5 cent rubber feet on the HW-19. Keep the Sorbo Pucks, they are hard to improve upon.

Some might laugh, but virtually any Tonearm could make its home on the HW-19, provided it will fit. Mark

Although VPI has discontinued production of the HW-19 Series, they still do carry some of the parts needed to do upgrades to the Table.

They sell what they call a MK-IV Plinth, which is sort of similar to the originally made MK-IV Plinth, but is now only a one piece sheet of 1/2" Black Acrylic, with a Steel Sub Chassis Plate. Price I believe is $300 shipped for it, and I'm quite certain that VPI will gladly pre-drill the Plinth Sheet for an Arm of Choice.

If they would possibly not have the specs on hand for any given choice of Tonearm, then all they would simply need is the Arm Mounting Template, and Tonearm Base Specs.

The only possible downside to this one piece Plinth, is if using a very thick Platter, rather than the thinner Junior Platter, one might have to have a Tonearm Mounting Base Spacer made to lift the Arm higher for better.correct adjustability of VTA height of the Arm.

Just about every Platter VPI ever made, past and present will fit the HW-19 Series, with the exception of the now gone Super Platter that was specifically designed for the Flagship HR-X Table.

AudioPoints, and others make direct replacement thread in 10/32 Brass Cone Point Feet, and Coupling Discs, that not only improve sonics to quite an extent, but also vastly improve the look of the Table as well.

The SAMA (Stand Alone Motor Assembly is still available, but improvements-tweaks can be made within the HW-19, to better isolate the original 600rpm Hurst Motor and its Bracketry.

The SAMA is actually the exact same 600rpm Hurst Motor, but it is within its own Metal Case, and thus is seperated from the Table's Base.

The VPI SDS is as well another option, and can be used with every VPI Table ever made, as well as other Belt Drive Tables that use an AC Synchronous Drive Motor.

You have made no mention of what Tonearm is presently on your HW-19? If a Rega RB-300, I believe the Origin Live Silver will be a direct drop in fit. If Audioquest, and at 211mm S-P, the Jelco ST-250ST should be a direct drop in fit, and is a good Arm for the little money spent.

Sure, you could probably place a Graham Arm, TriPlanar, or other very costly Arm on the Table, but some might say it would be akin to placing a silk hat on a pig. None the less, a Tonearm contributes a lot to a Table's final sonics, the better the Arm, often the better the sound without a doubt.

There's many audiophiles here who change Cartridges almost like I change socks, and thus, one can often find a very nice low hour MC, or MM Cartridge with a good savings versus new.

Over the years, I have upgraded my own HW-19 Table, even though some parts were no longer made, almost all the parts came from right here, used from other members.

When the parts surfaced, that was when I bought them, and the Table, which was once a work in progress has been taken just about as far as it can go.

My Table is outstanding in it's performance, teamed with an AQ-9 Arm, MK-IV Platter, custom Clamp, ZYX Airy 3X Cartridge, and Sutherland PhD Phono Stage. With the custom Plinth, Brass feet, custom 1.00" Black Acrylic Plinth, it is also a stunning looking "classic".

I think it would take a lot of $$$$ Table/Arm to drastically outdo this one I have. Mark

I'm fairly handy, and can assemble, lube, or mount parts without getting into too much trouble.

Still, when I decided to upgrade from the MDF Junior Plinth, to something different, I purchased the 1.00" thick Black Acrylic Plinth already pre-cut to size from a Plastics Company, and then took that brand new Sheet, and the original MDF Plinth to an accomplished machinist.

What he did, was pretty much copy the original, and made a clone, but insured that the 211mm S-P distance for the required Tonearm was within +- .003" tolerance. VPI was a little "off" on the Original Plinth's S-P spec by about 2mm.

I was originally seriously kicking around using 1.00" Aluminum Sheet as a Plinth Material instead, and this Material can be acquired from places such as McMaster-Carr. Was going to have it cut slightly oversize, let the machinist cut it to proper precise size, do all the needed machining-drilling-tapping, polish the top surface, then send it out to an Anodizer, and have it Black Anodized.

I think the Sheet of Aluminum a few years back was something like $125. And add about $200 for machining fees, and then the costs for anodizing.

I later decided Acrylic would be suitable, attractive, have good sonic qualities, since VPI also thought it was a worthy material, less expensive, but not easier to work with the Machinist claimed. Acylic when being worked has a nasty habit due to static electricity of sticking to everything!

I substituted the stock Sorbothane Puck Suspension with four Herbies Firm Tall Tenderfeet due to the added weight of Plinth, solid Steel Sub-Chassis Sheet under the Plinth, and a 16lb Mk-IV Platter. In stock Junior form, the standard firmness Tall Tenderfeet would work fine. Herbies Grungebuster Discs, and Washers were utilized all over the place on the table to very good effect.

My Table is a somewhat very similar clone to an original HW-19 MK-IV Table. I wanted to keep a very similar theme, and look, yet added a few nice touches-improvements.

The folks at VPI have seen Pics of it, and they were quite impressed. So was my buddy Doug Deacon here, saying it was the nicest HW-19 Table he's ever seen.

The beauty of the HW-19, is that it can be "personalized" in so many different ways ala Home Improvement center practically. As one example, one gentleman over on akarma took his Oak Base, to a Guitar Luthier, and had them shoot the Base in Tobacco Sunburst Finish. His reminds me of a Fender Stratocaster! Very nice.

If I can ever me of further service, and help to you, and others here, you are more than welcome to contact me.
Mark