Upgrading path from Merlin VSM black magic


Goal:
I have been tinkering with the idea of upgrading and investing in floor standers that are superior in every way compared to Merlins. What are the Merlin users upgrading to? budget is 25k or under (used market value).
My present system:
I am using my Merlins VSM Black magic with dual BAMs with Coincident tech Frankenstein mono block amps (300B SET) and coincident tech line-state and phono preamp. Whole system is wired with Cardas clear cables. Using EMM XDS-1 and VPI classic turntable. System was built around Merlins. I suppose I might have to pick electronics suitable for the replacement speakers and in that case will build the whole system again. Preferably, I would like to keep the front end electronics/amps/pre-amp etc.
My music taste:
I listen mostly Jazz, Classical and vocals. 
My room:
I had Merlins setup in 12x16x8 room which was fully treated. I have since moved to a larger-ish space 15' x 21' x 9'. The room is not treated yet but would be fully treated with absorption panels/diffusors etc in the near future. I setup speakers with ears and with RoomEq software. 
Why not Merlins .. ??
I have thoroughly enjoyed Merlins but sometime feel it can sound a little thin and won't reach the lowest bass. Larger sound stage is desired. Full scale classical music can have better depth, width and weight. I have been using various versions of Merlins since 2009 and have the last version produced (Black magic) with dual BAMs. I have purchased two Funk Audio subwoofers that I have not integrated with the system yet. Merlin is not very subwoofer friendly anyways.
What I am looking for:
Ideal speakers would get from "Merlin" its neutral, resolving, transparent, low distortion, dynamic character. On top would also deliver fuller sound (top to bottom), be a full range down to 20Hz, provide bigger sound stage and has a more organic / relaxing sound (..better emotional connectivity). Speakers should be tube friendly, (preferably SET or OTL).
Brands:
There are simply too many out there. These brands come to mind: dynaudio, magico, sonus-faber, mbl, B&W, wilson audio, rockport, jm-labs, dunlavy, wilson benesch.  I am sure someone who has owned Merlins and made a move can give their input. Even a short list to audition would be helpful. I am based out of Orlando area. Would be great If any local member has a system that they can allow me to audition.
Past experience:
Other notable speakers I have owned in past include original Flocal Utopias (mezzo to grand Utopia), B&W nautilus series, Quad 989 among others. Yesterday's nautilus 800, 802 were power hungry and sounded boxy. This may not be the case with the newer models.  I feel like I am out of touch with what is out there. Have been out of market for long. 
Thanks.



celestial_audio

Showing 4 responses by dgarretson

The BBAM embellishes with augmentation well up into the mid-range region. You may find that removing it causes more problems than it solves. 

A further thought about the BBAM.  It allows one 6.5" driver to act as a  time and phase coherent point source across a wide range from 2kHz down to 30Hz.  This(together with the superb silk dome Dynaudio Esotar tweeter) is part of the charm of the design.  For a time I tried a Velodyne DD-15 rolled in at 35Hz.  It vastly increased scale and impact, but I could never get the timing quite right, and eventually learned to live with the VSMs sub-less.

@tubegroover  My VSM and BBAM are both highly modified with premium caps, resistors, cabinet modifications, and a Paul Hynes SR7 power supply for the BBAM.  I wouldn't want to be without the modified BBAM.  The stock NiCad battery supply seriously limited performance of the BBAM.

@sstalwar & Rich

I don’t have a schematic for the BBAM. It’s a fairly simple circuit with capacitive filters and one AD744 op amp per signal phase. The Hovland coupling and filtering caps are easily surpassed. Replace them with best caps you can afford that fit on the PCB. I tried Mundorf SG and later switched to ClarityCap MR. You can also fit Duelund or V-Cap teflon. The stock Caddock MK-132 resistors are very good by high-end standards, but Texas Components TX2575 are more resolving and transparent. The stock AD744 is an excellent op amp. The big move is to re-power the AD744 with an external +/- 12Vdc bipolar linear supply like Hynes, Pardo, or Twisted Pear DIY kit. That means removing the stock batteries and 3-pin regulators from the PCB and running wires directly from the PCB to a panel connector. The current draw is tiny. Yes, a Hynes bipolar supply is >$1K. The others are much cheaper. IMO a well-powered op amp can rival tubes.

Rich, great that you continue to support the Merlin community. As good as the VSM series was/is, I wish that Bobby had carried the model forward with a serious update with slam for larger rooms. One idea would be to add a couple more 6.5" drivers to make a line array. Pretty much the same simple two-way second-order crossover, BBAM, and slim cabinet profile, but with increased output and headroom. Nice if you could explore it...