2. misc-audio
  3. 131672-481

The new Synergistic Research BLUE fuses ....

New SR BLUE fuse thread ...

I’ve replaced all 5 of the SR BLACK fuses in my system with the new SR BLUE fuses. Cold, out of the box, the BLUE fuses stomped the fully broken-in SR BLACKS in a big way. As good as the SR BLACK fuses were/are, especially in comparison with the SR RED fuses, SR has found another break-through in fuses.

1. Musicality ... The system is totally seamless at this point. Its as if there is no system in the room, only a wall to wall, front to back and floor to ceiling music presentation with true to life tonality from the various instruments.

2. Extension ... I’ve seemed to gain about an octave in low bass response. This has the effect of putting more meat on the bones of the instruments. Highs are very extended, breathing new life into my magic percussion recordings. Vibes, chimes, bells, and triangles positioned in the rear of the orchestra all have improved. I’ve experienced no roll-off of the highs what so ever with the new BLUE fuses. Just a more relaxed natural presentation.

3. Dynamics ... This is a huge improvement over the BLACK fuses. Piano and vibes fans ... this is fantastic.

I have a Japanese audiophile CD of Flamenco music ... the foot stomps on the stage, the hand clapping and the castanets are present like never before. Want to hear natural sounding castanets? Get the BLUE fuses.

4. Mid range ... Ha! Put on your favorite Ben Webster album ... and a pair of adult diapers. Play Chris Connor singing "All About Ronnie," its to die for.

Quick .... someone here HAS to buy this double album. Its a bargain at this price. Audiophile sound, excellent performance by the one and only Chris Connor. Yes, its mono ... but so what? Its so good you won’t miss the stereo effects. If you’re the lucky person who scores this album, please post your results here.

http://www.ebay.com/itm/ULTRASONIC-CLEAN-The-Finest-Of-CHRIS-CONNOR-Bethlehem-Jazz-1975-NM-UNPLAYED-...

Overall impressions:

Where the RED fuses took about 20 hours to sound their best, and the BLACK fuses took upwards of 200 hours of total break-in, the BLUE fuses sounded really good right out of the box ... and that’s without doing anything about proper directional positioning. Not that the BLUE fuses don’t need breaking in, they do. The improvement continues through week three. Its a gradual break-in thing where each listening session is better than the last.

Everything I described above continues to break new ground in my system as the fuses continue breaking in. Quite honestly, I find it difficult to tear myself away from the system in order to get things done. Its truly been transformed into a magical music machine. With the expenditure of $150.00 and a 30 day return policy there’s really nothing to lose. In my system, its like upgrading to a better pre amp, amp, CD player or phono stage. Highly recommended.

Kudos to Ted Denney and the entire staff at SR. Amazing stuff, guys. :-)

Frank

PS: If you try the SR BLUE fuses, please post your results here. Seems the naysayers, the Debbie Downers and Negative Nellie’s have hijacked the original RED fuse thread. A pox on their houses and their Pioneer receivers.

Frank



128x128oregonpapa
georgehifi's avatar
georgehifi
10,312 posts
 

OMG!!!!!!!!!!

If there were micro arcing on the end caps of mains fuses, you would see burn pits all over them, more "snake oil"

As for noise, if there were any, which I highly doubt, it couldn’t get through the transformer, rectifiers, smoothing capacitors, regulators, and more smoothing caps that come after the mains fuse, again more "snake oil"

The only reason a fuse may sound better after it’s replaced with either the same standard one or "snake oil one" is because of ageing, too may turn on cycles will age any fuse and cause it to deteriorate. All explained below.

Mapman inadvertently is agreeing with what really happens to a partially melted fuse, it’s called ageing. Good for you.

Funny this should be mentioned as it’s just like what happens to a fuse that’s seen too many turn on cycles, as there’s far more current goes through it at the moment of switch on than any other time, as it has to charge up empty power supply caps ect. that’s why fuses and light globes blow (if nothings wrong) at time of turn on, here are some pics of fuse ageing.

A slow-blo fuse "ageing" right to left
https://peakpinball.com/wp-content/uploads/2013/01/fuse-8312-640x426.jpg

A fast-blo fuse "ageing" left to right
https://i.stack.imgur.com/0uqWX.jpg%20



Cheers George
nonoise's avatar
nonoise
10,544 posts
 
If there were micro arcing on the end caps of mains fuses, you would see burn pits all over them, more "snake oil"
Are you saying you can see inside a fuse's end caps?
That's amazing George.
As for noise, if there were any, which I highly doubt
So you're not 100% sure? Nice to know....you're getting there.
The only reason a fuse may sound better after it’s replaced with either the same standard one or "snake oil one" is because of ageing, too may turn on cycles will age any fuse and cause it to deteriorate. All explained below.
Nope. That's been discounted already George. High rupturing fuses (the type that aftermarket fuses are modeled after) are filled with powder to keep them from arcing when specs are exceeded. A side benefit is that it greatly reduces heat and aging (the correct way to spell it) which prolongs the life of the fuse, many times that of a cheap, off the shelf fuse. Google it if you don't believe me.

All the best,
Nonoise

uberwaltz's avatar
uberwaltz
13,381 posts
 
And right on cue George!
Bravo.
We only seen that post about 50 times, needed the refresher...thank you!
georgehifi's avatar
georgehifi
10,312 posts
 
Are you saying you can see inside a fuse’s end caps?


What are you on, the supposed arcing is happening between the end cap and the fuse clamp, it not inside the end cap you ******* ****!!!!

You guys are so full of this "snake oil" you have no idea of even basic electronics.


Cheers George
nonoise's avatar
nonoise
10,544 posts
 
Are you forgetting that "micro arcing" occurs where things are connected?
Like when the fuse wire is soldered to the "inside" of the end cap?
Do you think that the fuse wire just lays against the inside of the end cap?
Do you see graphene on the outside of the end cap?
If it was, people would have figured it out already, genius.

By the way, I'm talking about the graphene that's used on the SR fuse and not the TC product.
Are you**************!!!!

All the best,
Nonoise
More to discover