Need help building an amplifier-headphone adapter


Hello

I have an integrated amplifier (12W) that does not have a headphone output and I want to find a way to listen via headphones.

The easy solution would be to find a device like the ASL UHC. But I have not managed to find one for sale in Europe.

http://www.divertech.com/asluhcsignature.html

Now I want to try to build one myself :) Could be a nice project and will add a nice feature to my amplifier.

Does anyone here have experience building such a device as the ASL UHC? Are there any kits or schematics available?

Thanks for any advice.
indiesverige
Thank you for the most detailed answer and explaining the different options and the notes of caution. I really appreciate the time you took for this. I am going to find a high impedance headphone and then buy some resistors.

It probably would have been easy to just buy a integrated amplifier with a headphone output, but I am very happy with the amp I already have now and just need a nice night time listening solution.

Happy listening to you all.
You may consider the AKG K1000 headphones which usually sell for about 1000 USD (!) on the used market. They are designed to connect directly to amplifier outputs, as they are sometimes referred to as "ear speakers"
I use a pair run off of 9 watt SET amplifiers or another pair of 2watt SET amplifiers.
I did a quick Google search and I see that the Shindo Apetite has no tape or other line-level output; it has only one set of output terminals per channel, rather than multiple taps; it is rated at 15 watts into 8 ohms; and it certainly has an output transformer since its output stage consists of a push-pull pair of 6V6 tubes per channel.

If the headphones are low impedance, for example 32 ohms, then as Czarivey pointed out driving them directly from the amplifier outputs would risk blowing up the headphones and/or your ears if the volume control is not kept very close to the bottom of its range.

If the headphones are high impedance, for example 300 ohms or more, that would be less of a problem but you would risk damaging the amplifier if you simply connected the phones directly to it. A tube amp having an output transformer should never be operated without a speaker or equivalent load being connected, or the output transformer and/or the output tubes may be damaged due to what is called "inductive kickback." I would expect that a load that is measured in hundreds of ohms, and perhaps even less, would be high enough to make that risk a real possibility.

One possible approach would be to get a pair of high impedance phones, such as this 600 ohm model from Beyerdynamic, or one of several other high impedance models they offer, and connect it to the amplifier outputs in parallel with an 8 ohm high power resistor, rated to handle say 20 or 25 watts or thereabouts and preferably a non-inductive type, one resistor for each channel.

That should work, although I suspect that you would still have to be careful with the volume control setting.

Alternatively, if you can find a suitable matching transformer, that would step down the amplifier's output voltage enough to be in a good area relative to the impedance and sensitivity of the phones, you could use that together with a similar 8 ohm high power resistor connected across the primary of the transformer (or, equivalently, connected across the output terminals of the amplifier), for each channel. (Without the resistor a step-down transformer between the amplifier outputs and the headphones would cause the amplifier to see an even higher impedance than if the headphones were connected directly to it, causing an even greater risk of inductive kickback damage).

A third possible approach would be to connect a high power resistor that is a little higher than 8 ohms across each channel, and in parallel with it connect 2 additional resistors that are in series with each other. The signal to the phones would be taken across one of those two resistors, whose values would be chosen to divide down the amplifier's output voltage by an amount that would be calculated based on the impedance and sensitivity of the particular phones. For several reasons it would be preferable to use that approach with phones having medium or high impedance, and avoid using phones having low impedance.

Regards,
-- Al
"How would I find out if this has an output transformer and what its impedance would be?"

Try to pick it up. If its really heavy, then yes, it has an output transformer. As far as impedance goes, it should be labelled by the speaker terminals. You could also check your owners manual. All that info is listed.
My amp is a Shindo Apetite.

How would I find out if this has an output transformer and what its impedance would be?
"If you have an output transformer in your amp, you'll need to find another transformer to match impedance of your headphones.
Czarivey (Threads | Answers | This Thread)

02-18-14: Yogiboy
Czaivey,Won't your preamp control the volume just like it does with speakers?"

I think he means having a situation where a very small change on your volume knob gives a very big increase/decrease in volume. Its very hard to control when that happens.
Czaivey,Won't your preamp control the volume just like it does with speakers?
You may do as Yogiboy did with directly coupled output stage amplifier. That will work if you have relatively high impedance headphones. If you don't, you won't be able to control the volume correctly and will have a chance of blowing either your ears or headphones whichever comes first.
If you have an output transformer in your amp, you'll need to find another transformer to match impedance of your headphones.
I use a headphone extension cable. I cut the male end off and hook up the bare wire to the speaker outputs of my amp! There are 3 wires when you do this,left,right and the ground that will go to both channels!
I think he wants to use the power amp section of the integrated to power his headphones directly.