Modding the PS Audio Directstream DAC MK1 and MK2


I would like to continue discussing all the mods we have created for these two DAC's as it seems PS Audio is no longer allowing discussions about them on their forum.

For reference here is a link to the closed discussion.

https://forum.psaudio.com/t/modding-the-directstream-dac-mki/2680

128x128richardselectronics

Showing 4 responses by tekaudiospecialties1

Speaking of heat sink heat, I had to replace the transformer in a Mk1 this past week. But the original is a custom unit rated 8v secondaries, 2 x 25VA and not available. I chose an off the shelf 6V rated out 2 x 25VA unit and tg it's working fine, with less heat across the linear regs too of course. It's actually delivering about 7.4V AC V out in mine. The original toroid has a band shield, and there was room in there to wrap a band shield around the new one. I went with this one: Triad- VPT12_4170

TK

And may I ask, do we have any schematic info on the Mk2? Output section in particular? Thanks, TK

Hello folks, still here occasionally :) Thought I'd share some things.

The Vocm mod with JK high nickel trafos is quite good and would likely satisfy the majority of listeners IMO.

I will say though, the pinnacle of DS DAC mk1 sonic performance is, Diff amps topology mod (also found some diff amps I prefer to the AD803x), along with a bi-polar PSU that then allows for no caps or trafos on the output. This also allows Vocm to be=ground, so no mod needed for it anymore. It's not trivial to do but can be done, I'm listening to mine here now with it.

Now we're really talking, now there is no audible distortion (quite rare IME) and you are hearing the fw performance basically. Any further improvement would be upgraded fw. I asked if we could get a Mk2 version improved fw for Mk1 and the answer was no.

BTW I prefer the older Sunlight fw on mine; it's more open and dynamic and alive sounding. It's playing here now. 

I recall someone on the forum had done some topology mod effort, but they claimed they didn't like it. I don't know what the problem was there, and maybe I had also misguided somewhat with some poorly suggested values at the time. But whatever, I don't have the time or energy these days to try and maintain and acceptable S/N ratio of a web forum and that's when I called it quits there basically. The truth of it is what I posted above.

TK

Some other news, this summer I was able to get Tom C of Neurochrome Audio to do a special version of his Modulus "error correcting" amp boards (thanks Tom!). Notably, we eliminated the OA input buffer, and the input coupling cap (and feedback cap!) and added back a DC servo since its now DC coupled. IMO this should allow the most transparent Modulus you can do basically. I’ve been listienng to it for months (its playing here now with a new proto preamp) and it’s quite good in fact. Note that, with the OA input buffer gone the boards are single ended input only, which is fine. The amp modules themselves are also single ended anyway, as most amps are internally. And again, its fine.

However, for best results it does need the best OA we can manage for the "error correcting" portion, and for the DC servo. Most industrial OA are evil in comparison; discrete ones generally less so at least. I socketed my build and prefer the Sparkos SS3602 in the error correcting location and a Muses01 in the DC servo. Muses OA appear standard old industrial but they are far from it, employing a Cu leadframe for example. They put a lot of effort into these in fact and you can definitely hear it. The 01 is a JFET input and is very clean and quiet, also good for a DC servo IMO. The 02 is a bipolar input and "rocks" a bit more in comparison IME. But not as good for a DC servo due to input bias currents.

I have mine in a Naim NAP180 chassis with what I call a "super" PSU in it. I think I would recommend a good SMPS for it if DIY. As Tom says, with this much error correcting horsepower available the boards are somewhat immune to PSU, but still, better PSU is better in general.

If you want to DIY your own, ask Tom for the "Todd King" edition Modulus boards. I can recommend them.

TK