Mapleshade Silclear


Category: Accessories

I'm not a big proponent of the "WOW" factor, meaning very few tweaks have caused me to go "WOW". The wow ones include rebuilding my McCormack DNA .5 amp to near Rev A, changing the caps in my speakers from Axon's to Sonicaps, and few others. Now that doesn't mean I don't hear differences and improvements with other tweaks, it's just that I don't believe in overemphasizing these differences into religous revalations and such.

So, Silclear doesn't fall into the "WOW" category with me, but it did make an improvement in my rig. The simplest explanation of these changes I can make goes like this. Have you ever cleaned the contacts on your interconnects, speaker cables and power cords after a year or more of ignoring them? Did you hear the improvements in transparency and quieter backgrounds? Well I just cleaned everything over the New Year's holidays with cotton balls and alcohol with an application of SST (to signal wires) and Pro-Gold (to electrical connections) afterwards. Now, in February I applied Silclear to everything in my system that has a plug, jack or socket. This means interconnects, speaker cables, fuses, all electrical jacks inside my amp & CD player and DAC, electrical cords, tube pins, phono cartridge pins, etc. The difference was as if I left all these connections to tarnish for a year or more and then cleaned them all again.

Now, given that I just did the cleaning I can conclude that Silclear took this one step farther than alcohol and SST. Things were more transparent and noticeably punchier. The bass was louder (dammit - I had to turn down the sub's volume and rebalance the bottom end again). Soundstaging and imaging seemed to be a slight/tiny bit more forward than before, maybe because things seemed a bit louder at the same volume settings. Tonally everything was still balanced, just more there in terms of detail and nuance and definition. But I also found that there was a sense of more "realness" to instruments, especially cymbals (hearing more brass with the zing), and voice (more in the room presence), and piano (more body and weight). The system sounded quieter too - i.e. blacker backgrounds (but this can also vary by time of day as the power grid changes).

Is this a "wow" review in disguise? Perhaps for many it is, but I already have a whole lot of transparency and realness in my system (see "Isn't Anything Stock?" for my system details). I now have more of that than before.

I really can't report that there were any bad aftereffects of the Silclear either. There's no way to undo the application easily (it's a grease), so there's no A-B testing available. So many tweaks improve on thing at the expense of another - not here. It's a good thing (thank you Martha Stewart, now go directly to jail and don't pass "GO").

Enjoy,
Bob
ptmconsulting

Showing 3 responses by knownothing

Curious if people who were enthusiastic about this product are still enjoying silclear several years after first application? If you changed equipment or wires, did you reapply the product? Sounds like biggest problems had to do with application on tube pins where heat combined with vertical installation may be a problem - but perhaps also issues related to other connections?

Seems to me that an oil based product like this would work best if applied to a layer of only a few particles thick, filling any surface imperfections with sliver "platelets" and wiping the excess off each connector. I am planning to apply to my SS system, and wondering if others who have lived with this product for a long time have any further advice, warnings or other comments.

Thanks in advance for your thoughts.
Ckorody,

You said "Also it leaves silver stains on connector housings". Actually, I think that is the point, to produce a semi-fluid silver "stain" on the blades of your connectors as opposed to a visible layer of silver and oil goo. I am skeptical of the oil emulsion's stability over time, and having a "gooey" mess form sounds "counter-conductive" to me.

I am also questioning the need for applying any contact enhancer or cleaner to silver or gold (or rhodium) contacts. Silver is already highly conductive and actually tarnishes to become more conductive, and gold doesn't tarnish much if at all over time. Gold is slightly less conductive than silver, so it is possible a thin layer of silver product applied to gold interconnects and RCA connectors could theoretically, and apparently empirically, produce an improvement in signal transmission. So perhaps a VERY thin layer (or "stain") of Silclear on gold connectors would improve performance.

Where I am thinking Silclear should provide a distinct improvement in electrical contact and conductivity is on copper or brass AC plugs and internal wire terminations, and on copper speaker wire terminations. Here the better conductivity of silver and benign effect of silver tarnish over time would make this an excellent contact surface for AC and speaker wire applications.

Since I am thinking about how to most productively use this stuff on my system, others thoughts appreciated on this topic.
Ckorody,

Helpful information. Yes, ultimate goal is to get rid of all brass. In the meantime, I am trying some poor man's silver plating.