Making phono resistance plugs

Any ideas about making a pair? Looks simple. Any esoteric suggestions? Need a little over 400 ohm. Any particular brand of resistor, or plug? 
81788a71 d1eb 4b1b acf9 bf8650bf8481coachpoconnor

Appreciate your feedback. I will definitely give it a shot later this afternoon. The E-Glo phono uses toggle switch to adjust load and gain (I deliberately pick this phono for easier operation rather than crawling back or messing with dip switches).

What you say is makes sense...I need to be bit more patient with the process. I knew going into Analog there is going to be a steep learning curve until you achieve that blissful analog sound :-)
 Definitely it would not be "magic".

Not my words the guy that built it.. Look mid page "Tape option"

I'm a tinker, a mechanic, rules? I thought they were meant to be tested, broken, changed.. LOL That's me.. Yea you can add a pot...No problem..
Sound better, different, worse, OH YEA... BUT MAYBE, just what YOU want... The reason I went with one...A POT.. Yup.. See Decware idea..
Why won't it work for vinyl? I'll try it...

I'm thinking, who is making mag heads for RtRs, ME...Why not me...
Just need to do a little tinkering...

Enjoy in any case. Easy is alway good.. I like everything on top or in front.. If I don't want things changed they go inside..

Have fun.. Time to feed the chickens..they're glad they are not turkeys...

I think you need to contact Whest to determine the proper resistance value of loading plugs to use with your PS.20. I just looked up the PS.20 Operating Manual, and that is what it advises. Since none of us know the internal resistance of the PS.20, and whether the plugs are in series or parallel to the internal signal path, we can’t help. If you have a multimeter, you could measure the resistance of the plugs used for 100 ohm loading. If we know that we could help you get to 400 ohms.
My phono pre also has the large step from 100 ohm to 1000 ohm loading. I tried a Y-adapter to add parallel loading plugs, but decided I like the Audioquest “Hard RCA Splitter” better. See
I use a resistor about 1000 ohms in parallel with the 1000 ohm setting to get to about 500 ohms load resistance. I made a bunch of plugs to try various loading between 100 and 1000 ohms, and settled on the 500 ohms loading. 
The recommended load setting for my Hana Umami Red is >60 ohms.
Fortunately my phono allows me to adjust gain and load on the fly

(EAT E-Glo S). My phono load settings are, adjust gain and load on the fly  (EAT E-Glo S). My phono load settings are,
10R, 30R, 50R, 90R, 100R, 1K, 47K.


Give me a schematic, I can figure it out...

Series, Parallel or both. AND Stick  a pot in there, just for good measure. LOL

Greater than 60 ohms. Parallel.  My thinking, put a pot before the resistor, and run the other end of the resistor to the neg. Then you can very the choice, between the two values.. IF I'M wrong, then how can that "idea" be implemented? That's MY question, I'm a common ol mechanic. I want to learn too. LOL.. I'm an Old Dog, I can still learn a new trick or two..

I think if it was hooked up to 100 and lPad down to 60. Something like that.. How do you do that? Teach me..

Thanks OP, I know you understand, you SEEM as picky, and nosey as me.. LOL,  BIG :-). Tinker fest USA here... Just my nature...

So we're clear, all my STUFF is coming out of storage, I know I forgot more than I can remember.  I gotta start firing on all 6.. 153624, To young, to old, just right. Military memory.. 36 to OLD, NOW WAY to young. :-)