Impedance Question?


OK so I know there's a lot of threads about matching impedance with pre/amp.  It would be really nice if someone could help out here! The whole impedance thing confuses me (doesn't take much).

So if I have an amp that has 10k impedance what range for output impedance would work for a preamp?

Any help would be great!
sqitis
Maybe this was mentioned and I missed it but is there a simple mathematical relationship between the value of the coupling capacitors and the output impedance or other variables are in play?
There is-  Zout+C, where C is the impedance of the cap at the specified frequency, and Zout is the output impedance of the circuit driving the cap.

At 1000Hz, typically the cap has no influence on the output impedance. But as the frequency is decreased, the output coupling cap begins to have a greater and greater influence as the cutoff (-3db point) frequency is approached, such that it is the major component of the output impedance rather than the circuit driving it.

Keep in mind that this is a bit oversimplified as there can be complicating aspects that do affect output impedance, such as the application of loop feedback which will reduce some of the effects of the output coupling cap.
 Very informative thread. Thanks for asking the question sqitis. Maybe this was mentioned and I missed it but is there a simple mathematical relationship between the value of the coupling capacitors and the output impedance or other variables are in play?
I’m curious to know what these issues are with direct-coupling are since I may go this path with the SLP-98.
The Cary employs direct-coupling but not at its output- there it uses a conventional coupling capacitor.

But to answer the question, direct-coupling issues are
1) the unit must not make DC that could damage an amp or speaker
2) the DC must be able to stabilize during warmup without damage to amp or speaker
3) This requires a servo control; the servo circuit must be stable at all input signal conditions and not impart any sound of its own

The tricky bit is actually 2) above, in many solutions a protection relay is used and the relay itself can contribute (or rob from; depends on how you look at it) to the sound. We patented a circuit that is reliable enough that a protection relay is not needed.

I may have overshot here- in case you were only asking about the direct-coupling used prior to the output of the Cary. If that is the case, the big issue is power supply stability, as the circuit, except for the output, has bandwidth to DC. Power supplies, even though they are a source of DC, have a timing constant that is something just shy of actual DC like a battery has. If the circuit can go lower than the power supply, low frequency instability can result. 'Motorboating' which is a problem in amps and preamps with failing power supplies, is an example of this phenomena.


Why would they not use a higher value capacitor if that improves the sound and provides more pairing options?


1: Cost, the larger uF the more expensive.
2: Size, the larger uF the more real-estate it takes up.
3: The sound deterioration the larger uF you go.

Cheers George


 
I’m curious to know what these issues are with direct-coupling are since I may go this path with the SLP-98.

Great info here fellas! Keep it up!

Ben
Why would they not use a higher value capacitor if that improves the sound and provides more pairing options? Cost can't be the reason since the price differences is not much. There must be other reasons or design tradeoffs.
You are correct. The bigger the cap, the more coloration it will impart, regardless of the dielectric. As a result, you want the smallest cap to do the job right, if low coloration is your goal. A 0.47uf cap sounds noticeably better than a 5.0uf cap; capacitors are wound on a machine so they have not only capacitive qualities but also inductance and resistive qualities as well. The dielectric (Teflon, paper, polypropylene, etc) affects the sound as does the length and diameter of the part.

This is the main reason that some tube preamps don't play nice with some solid state amps. The coupling cap is too small, and one big enough imparts more coloration than the manufacturer is willing to accept. So the manufacturer solves the problem by declaration (example: ARC limits their preamps to power amps with 30K or more input impedance). We solved it by direct-coupling; others use output transformers (which have a different set of issues).

Why would they not use a higher value capacitor if that improves the sound and provides more pairing options? Cost can't be the reason since the price differences is not much. There must be other reasons or design tradeoffs.

Yes that’s if the coupling cap is 5uF that I used as a hypothetical.
If it's 1uf the -3dB is at 16hz. or .47uf the -3db at 32hz

Cheers George
Yes it's 10k according to SL. So that's only down 3db at 3.18hz?  I can live that if so....LOL
You say your amp this 10kohm, this is the 10000 in the formula, and the 5 is the 5uf cap I said should be the minimum for -3db at 3.18hz bass rolloff.

Cheers George 
Wait, the answer is a number (I've yet to calculate). Is that the gain or the frequency? How do you find the other?
Before anyone corrects me on pie, I’m an Aussie we love our beer, meat pie’s/ with blood.

Cheers George
(2 pie x 10kohm x 5uf)

6.28 x 10000 x 5 to the minus 6, = then 1/x (reciprocal) the answer
which equals -3db @ 3.18hz

Cheers George


@georgehifi oh man, sorry. I didn't mean to repeat myself. I've the schematics for my pre somewhere, I'll see if I can figure out what value the coupling cap is. 
What formulae are you using to calculate low frequency roll off?
And that is why I'm leaning towards a direct coupled SLP-98 with some 50's JAN tubes.
The Dared apparently has a low input impedance.
Yes as you stated 100ohms in your previous post, which will drive any poweramp.

But being a tube it will be capacitor coupled, and if that cap is not big enough in uF, that 100ohms output impedance can start to rise in the bass and increase that 100ohms, and if it rises enough, into a 10kohm amp you could get bass rolloff.

The cap needs to be at least 5uF into 10kohm, to be rolling off the bass -3db at 3hz which just starting to rolloff at 20hz

This is why direct coupling is so good, no cap to **** things up and to colour the sound.
Best cap is no cap.

Cheers George
That said, I have a Dared MC7P (there’s a dash in there somewhere..) and it played nicely with a Crown amp that had in input impedance of 10k and currently plays well with ICEpower monoblocks. The Dared apparently has a low input impedance.

It’s all so freaking variable!
jmcgrogan2 has the best answer +1

Our tube preamps don't have an output coupling cap- so they can drive 600 ohms let along 10,000 ohms with ease. The output impedance is the same at 5Hz as it is at 1KHz or 30KHz.

Generally speaking though, most tube preamps are likely not to play bass right driving 10K, simply because of the output coupling cap being too small.
Well, I'd say you should trust the manufacturers more than us. But putting together what they both said, I'd say they seem like they'd work. Proof is in listening, of course
OK thank you guys!! So I was discussing with Dan ModWright about his 2 preamps and he said either of his would work LS36.5 110ohm and the LS100 300ohm.
Do you guys agree and feel that those pre’s will match up with 10k input on SL RG1?
OK so I got an email back from Rolf at SL and he suggest staying 100-300ohm.

I would agree with this recommendation. Many say the general rule is 10:1, Amp input impedance:preamp output impedance.

However, in many cases this is not enough. Many manufacturers, like Audio Research, recommend a 20:1 or 30:1 minimum ratio.
The main reason is because most stated preamp output impedance is not a ruler flat measurement, but rises quite a bit in the lower bass regions.

For example, my ARC Ref 5 preamp has an output impedance rating of 600 ohms (balanced). ARC, the preamp manufacturer, recommends an amp load of a minimum 20K input impedance (33:1 ratio).
The reason being that measurements show the output impedance of the Ref 5 rises to 1447 ohms at 20 HZ.

This is common with many tube preamps, the stated output impedance can more than double in the lowest octave.

Another example is the Cary SLP-98 that you mention. The spec sheet states a 800 ohms output impedance.
According to Stereophile measurements, " The output impedance in the midrange and treble was usefully low, at 370 ohms, but this rose at 20Hz to 6.8k ohms, due to the limited size of the output coupling capacitors."


In a nutshell, your manufacturers recommendation of a preamp with an output impedance of 100-300 is a good one for an amp with a 10K input impedance. This will eliminate most tube preamps, but not all.

Cheers,
John

It is so confusing isn't it?! I'm currently looking at room measurement mics so I can stop going completely by 'feel'.

Good luck! I use a dared mc7-p preamp (class a tube) with my class d monos and it sounds beautiful. I think it only has an output impedance of 100 ohms and there is certainly no roll off in the bass zone.
OK so I got an email back from Rolf at SL and he suggest staying 100-300ohm.

Cary says that on the SLP-98 in the manual 800 but on the item page it says 440. LOL
Not all preamps that have equal output impedance specs, say 600 ohms, have the same impedance across the frequency band, and often much higher at the lower (bass) frequencies. The result would be a loss of mid/low bass with those having this condition when paired with an amp having low input impedance. 

To mate a preamp with a 10K input impedance amp one would need to know the output impedance of the preamp across the frequency range. 
And right now I'm using a pre that has 100-300ohm and can't figure out which is sounding better.....LOL  This damn hobby can drive me nuts at times but I still love it!

Thank you all for your help BTW!

Ben
Others have had issues regarding impedance. If the amplifier input impedance is 10k, it is really only suitable to match to a solid-state preamp. With a tube preamp, it can work, but you may start to see weak bass/midbass (among other issues). Look for a higher impedance amplifier. For example, the Parasound A21 has input impedance of 33k for RCA and 66k for balanced. I have seen other amps with input impedance of even 100k or 200k.
So I had this 10k (Symphonic Line RG1) hooked to a Cary (SLP-03) 500ohm and yea I lost some bass/midbass for sure and couldn’t figure it out. However I’ve heard the SL hooked to a SLP-98 (800ohm) and it sounded way better, So I’m trying to match a pre with this amp and need all the help I can get.

Would a pre that has 600ohm -<1Kohm be safe to match?
toddverrone554 posts09-29-2017 11:50amQuick and dirty answer: you want the amp to have an input impedance at least 10x the output impedance of the pre.

This is a good simple answer.

Cheers George
The amps input impedance should be 10 times the output impedance of the preamp. This is considered the minimum and since the preamps output impedance varies with frequency, it's better for the amp input impedance to be 15 or 20 times that of the preamp.

So if your amp is 10k, then the preamp should absolutely be no more than 1k, and to be safer the preamp should be in the range of 500.

Others have had issues regarding impedance.  If the amplifier input impedance is 10k, it is really only suitable to match to a solid-state preamp.  With a tube preamp, it can work, but you may start to see weak bass/midbass (among other issues).  Look for a higher impedance amplifier.  For example, the Parasound A21 has input impedance of 33k for RCA and 66k for balanced.  I have seen other amps with input impedance of even 100k or 200k.
So are we talking an impedance between 100-400ohm or higher for pre amp output impedance?  I think a range would help me understand.

Toddverrone - I read that thread and tried to figure it out...LOL
Quick and dirty answer: you want the amp to have an input impedance at least 10x the output impedance of the pre. 

Here's a solid thread: https://forum.audiogon.com/discussions/how-to-match-preamp-and-power-amp
Post removed 
Hi!

The issue is almost entirely related to tubes. The manufacturer will usually recommend a minimum recommended impedance, and anything more is better.

Stereophile will also test preamps with a variety of loads, and report on the effects,.

Best,

E