2. home-theater
  3. 1264577263

Ideal Preamp/Processor for 2-Channel & Phono Stage

My speakers (Zu Definition Pro) require bi-amplification becuase the front speakers are not wired to the rear speakers. Please don't focus on this, or the merits of Zu speakers, or room treatments. I'm looking for advice on a Pre/Pro to use in a 2-channel set up. No video necessary.

I need to equalize my room/system, so I am going to use a pre/pro. This is the only viable solution I'm considering because of the separate signals going to the front and rear speaker arrays.

Right now I'm using a Rane PEQ 55 for the rear array, but having the Rane in the signal path to my rear speakers can't cover the full tonal spectrum because it is only in the path to the rear speakers.

So, why am I only considering a "high-end" Pre/Pro in a 2-channel set up?
Inherint in the models I'm considering is the ability to equalize the front speaker array separately from the rear speaker array. How? By using the "front" speaker outputs for the front array and the subwoofer outputs for the rear array.

The Pre/Pro filters the low-frequency signal for subwoofers, so I would use that signal for the woofer array on my speakers. The front speakers output could be filtered for the front array. Then I can use the controls/software in the Pre/Pro to properly equalize my system/room.

The Integra DHC 80.1 has two mono subwoofer outputs, and the Classe SSP-800 has two stereo subwoofer outputs. Mono bass below 80Hz is not a problem since we cannot localize bass at that frequency or less.

My goal for this post is to get feedback from people who have listened to some of the high-end Pre/Pro equipment for a 2-channel system. Meridian is really nice, but outside my price range and I'm pretty confused with all the cards and versions. Other manufacturers would be greatly appreciated. If you're selling something, please contact me using my email address.

My turntable set up is really important to me and I don't want to sacrifice any (or at least as little as possible) of the benefits from it, so I'm looking for a Pre/Pro that also has an awesome phono stage.

I'm trying to stay away from using the word "best" because "best" is subjective and means different things to different people and threads with "best" spin out of control with questions like what are you trying to do, what do you want out of your system, etc... All helpful questions, but not the goal of this thread.

The only practical solution I'm willing to explore right now is to find a Pre/Pro that will allow me to equalize my room/system (using a mic would be ideal), has two subwoofer outputs (can be two mono or stereo outputs) with a great phono stage so I don't lose the benefit of my analog rig. Pretty straightforward.

My system:
Yamamoto A-08S driving the front speaker array
Berhinger EP2500 driving the rear woofer array
Canary CA-903 Line Stage
Canary CA-400 Phono Stage
Ayre CX-5e CDP
Avid Diva 2 TT
Zu Definition Pro speakers (MTM front 20kHz-50Hz, & 4-10" woofers rear 1kHz-15Hz)

Regards,
Mark
aceboympk

Showing 4 responses by aceboympk

aceboympk OP
33 posts
 
Dan_ed, I had a difficult time understanding the active line-level crossover for my configuration because there is not one signal, but two signals. Maybe you can contact me off-line or post a URL I can read to better understand it.

I MAY need to equalize higher up based on my room, though I won't know until the person setting up my system measures my room. Having that functionality available in my unit will be critical when the guy is here measuring and setting up my system. He travels to do this, so I need to accomplish as much as I can while he's here.

Why do you feel that bass under 80Hz can be localized? How would that be accomplished? What would I use to localize it?

Zephyr, I contemplated the SSP-600, but the 600 lacks the controls required by the person doing my set up. I also considered the highly regarded SMS, but I believe the frequency limit for the SMS (> 26Hz) is well above the bottom end of my speakers (10Hz) so I don't think it would fit in my setup. Also, my goal is to have only one processor in the chain so I don't add any more latency that is inherint in my speaker design with the front and rear speaker arrays.

Please keep the suggestions coming. They are extremely helpful.

Thanks,
Mark
aceboympk OP
33 posts
 
Jim,

I'll have to research the DRC-205 more, but my concern (as you addressed in your post) is the connectivity between the unit any my front and rear speaker arrays. Again, I'll look into it deeper because it looks like another viable option if I can run the signal to both arrays.

Thanks,
Mark
aceboympk OP
33 posts
 
Dan,

I know that article backward and forward (I also own the Yamamoto), but I missed the line-level cross over unless your referring to the Rane PEQ55 which I also own.

Take a look at this article about localizing the bass signal:
http://www.ultimateavmag.com/howto/805bass/index1.html
aceboympk OP
33 posts
 
Dan,

No need to apologize. I appreciate your feedback. You stated my "phono stage". My goal is to equalize my system/room using the pre/pro for all of my sources, not just my phono stage. I don't think using a pre/pro is the ideal solution, and I may not need to EQ the entire frequency range. However, my speakers require a unique configuration and solution. Thus, I may not be able to get the ideal or what I want...I may get what I need.

Regards,
Mark
More to discover