Hi Eddy,
Thank you kindly for the nice words.
I took a look at the specs on the LS-27, the 28Bsst2, the MAXX2, and the VTL MB750. I also looked at Stereophile’s reviews and measurements of the VTL and the MAXX2.
Also, BTW, I looked at the schematic for the 28Bsst2, because the input impedance spec listed in its manual was confusing. It turns out that its input impedance is actually a bit low to be optimal for use with your LS-27. The VTL would be fine in that respect.
The bottom line is that I don’t see anything that would be a showstopper if you were to replace the Bryston amp with the VTL, but there are a couple of things I would be concerned about.
Most significantly, I’m uncertain as to whether an objectionable degree of weakness might occur in the mid-bass region as a result of the interaction of the amp’s 1.3 or 1.8 ohm output impedance (depending on mode) and the challenging combinations of impedance magnitudes and impedance phase angles the MAAX2 presents in that region (see Figure 1 and JA’s comments just above it in the measurements section of Stereophile’s review).
A lesser but possibly significant concern involves gain. **If** you are presently operating the Bryston amps in their low gain mode (23 db), and **if** you were to use the VTL amp in its tetrode mode, which provides higher power and higher gain (31 db) than its triode mode, you would find yourself setting the preamp’s volume control about 8 db lower than the settings you presently use. If you are already using relatively low settings in the control’s range, and if you are already using the low gain settings of the preamp and therefore can’t make them any lower, that might result in having to use the volume control undesirably close to the bottom of its range. To provide some context, if the preamp’s volume control has its min setting at around 6:30 or 7 o’clock, and its max setting at around 5 or 5:30 o’clock, as a very rough approximation an 8 db change probably represents something like 60 degrees of rotation (although less than that near the bottom of the range, where volume changes probably occur more rapidly).
So in conclusion all I can offer in response to your question is a definite maybe :-)
Best of luck, however you decide to proceed. Regards,
-- Al
Thank you kindly for the nice words.
I took a look at the specs on the LS-27, the 28Bsst2, the MAXX2, and the VTL MB750. I also looked at Stereophile’s reviews and measurements of the VTL and the MAXX2.
Also, BTW, I looked at the schematic for the 28Bsst2, because the input impedance spec listed in its manual was confusing. It turns out that its input impedance is actually a bit low to be optimal for use with your LS-27. The VTL would be fine in that respect.
The bottom line is that I don’t see anything that would be a showstopper if you were to replace the Bryston amp with the VTL, but there are a couple of things I would be concerned about.
Most significantly, I’m uncertain as to whether an objectionable degree of weakness might occur in the mid-bass region as a result of the interaction of the amp’s 1.3 or 1.8 ohm output impedance (depending on mode) and the challenging combinations of impedance magnitudes and impedance phase angles the MAAX2 presents in that region (see Figure 1 and JA’s comments just above it in the measurements section of Stereophile’s review).
A lesser but possibly significant concern involves gain. **If** you are presently operating the Bryston amps in their low gain mode (23 db), and **if** you were to use the VTL amp in its tetrode mode, which provides higher power and higher gain (31 db) than its triode mode, you would find yourself setting the preamp’s volume control about 8 db lower than the settings you presently use. If you are already using relatively low settings in the control’s range, and if you are already using the low gain settings of the preamp and therefore can’t make them any lower, that might result in having to use the volume control undesirably close to the bottom of its range. To provide some context, if the preamp’s volume control has its min setting at around 6:30 or 7 o’clock, and its max setting at around 5 or 5:30 o’clock, as a very rough approximation an 8 db change probably represents something like 60 degrees of rotation (although less than that near the bottom of the range, where volume changes probably occur more rapidly).
So in conclusion all I can offer in response to your question is a definite maybe :-)
Best of luck, however you decide to proceed. Regards,
-- Al