Calling Lamm ML2.1 owners


I wonder if tube rolling those 6AK5 and 5651 tubes has any effects! Mine is over 10 years old and I have changed every other tubes but still keeping that 2 on the amp! Wonder how long can they last!
luna
I never looked for replacements, are there alternatives available? I made some experiments with 12AX7 but honestly, the Lamm Design is very stable in sonics.
Thanks Syntax but my questions is how long before I replace new ones as they are on the amp for 10 years now. I have replaced the 6n6p many times already!
Send Vlad an email, but I suspect you could use some fresh tubes. And my recollection was, those weren't necessarily expensive. The only one I roll in mine (ML2) is, like the Syntax, the 12ax7.
The 5651s are not expensive. About $8 each. I bought some because I had a problem with one amp where the 5651 went dark. When I looked inside, the internal fuse had blown.

Replaced the 5651 and the internal fuse and it worked for 20mins and the fuse blew again. I ran in mono for a while, thinking I had to send the amps to Lamm - which was a bit of a logistics issue. But finally I contacted Erina and she told me what to do.

The problem was that the 6C33C voltage regulator was old and not doing its job. I had a spare set of 4 x 6C33Cs from Lamm (all correct numbered parts for the amps) sitting in the cupboard. I replaced the whole set - they were all quite used up, one significantly so. These were the original valves, except for 1 - so they had done some miles (I bought the amps second hand).

There was actually nothing wrong with the 5651 voltage reference tube so I put it back in.

I've replaced the 6N6Ps once and will do so again in January. I use Pvane 12AX7s.

Regards,
In terms of those 6c33c. I have brought a set from Thetubestore and worked fine. I read that they need to be carefully matched but lucky not so in my case. It seems as long as it is within range for correct bias to be set, it is fine. I know the regulation tube actually goes sooner than the power tube. Cheers.
I own my ML2.1 maybe 4 years now and I haven't replaced any tube. The datas are all ok, the units are very reliable. But I use them with 99dB Speakers, anyway, there is worse out there...check the Pins (that they are clean), take care that the Tube sockets have a good grip, that's it.
I replaced my 6AK5's last Saturday. Although I checked them on a Hickok tV7 last December and they tested fine, I recently aqured a Mighty Mite IV tester and the life test/emssions showed they were poor. They had been installed for several years without issue, but there was a substantial improvement after the replacement (i.e. after 45 hours burn in). I have found the V2 6C33C to fail most frequently, followed by the 5651, V1 6C33C and finally 6N6p. 6AK5 is at the end of list as I have rolled the 12AX7 position several times to have any meaningful life expectancy judgement. The good thing about a failed V2 6C33C is that it can be used in the V1 position and vice versa, as the amps only use half the tube. So when I lose a V2 6C33C I just put it in a box for when a V1 goes sometime down the road.
Yesterday I replaced my first tube, a 6C33C-B after 3000h of use. The others still run strong. A pretty good tube design. Btw. when someone is interested to try a good 12AX7 tube without spending a fortune ---> Psvane
I have a question about the 6c33c tubes? The tube store is marking them form 18 - 39 on the box. I wonder what that means and which should I be using for V1 and V2 position to get the best match?
Thanks.