2. cables
  3. 138531-115778

Bi-Wire Advice for ProAc Response D2

Greetings from a new Audiogoner.  Recently acquired a pair of ProAc Response D2 via an Audiogon member.  Am thinking about bi-wire for these and am interested in any recommendations the community may have.  I currently have a Cambridge Audio 651A integrated amp (until I upgrade of course).

I'm thinking that Kimber Kable 8TC might be a candidate but I wanted to tap into the experience of this forum, even to hear whether you think bi-wiring is necessary.

Thanks in advance for considering.
goethe58
10 responses Add your response
Ag insider logo xs@2x
cleeds
5,642 posts
 
goethe58

acquired a pair of ProAc Response D2 via an Audiogon member.  Am thinking about bi-wire... I wanted to tap into the experience of this forum, even to hear whether you think bi-wiring is necessary
Bi-wiring is absolutely not necessary. Whether it's beneficial or not is a separate question. You'll likely get differing opinions on that, so you'll have to decide for yourself.
twoleftears's avatar
twoleftears
5,313 posts
 

I ran Response 2.5's both ways, and didn't notice any real difference.  Just be sure to replace the metal jumper bars with some quality jumper leads.  The same brand/model as the speaker wire is of course ideal.

All other things being equal, I think it's more cost-effective to put the $$ you would spend on two runs of wire towards a better grade of single run.

Of course, there are speakers that more or less demand bi-wiring; this isn't one of them.

jperry
2,430 posts
 
I have had a number of Proac speakers and found that I was better off with a higher quality single run and high quality jumpers.

My system is posted here if you want to look at it.
milpai's avatar
milpai
2,313 posts
 
+1 @jperry .
Completely with you on this! ProAcs need some good quality wires and jumpers.

Reach out to a good dealer and/or cable maker and see if they can make a nice pair of jumpers for you.
akg_ca's avatar
akg_ca
2,150 posts
 
This is a well-travelled off-repeating question dissected in AGON and just about every other audio forum.

Here is one on AGON worthy of prior research that is readily available in your journey

https://forum.audiogon.com/discussions/bi-wire-or-not-to-bi-wire

In brief:

(1) It is always system dependent as best evidence ,

(2) Without prejudice of the above, an increasing number of major manufacturers are advocating a best-of-breed single run and jumpers array.

CHORD even stopped making dedicated bi-wires.
Post removed 
b4icu's avatar
b4icu
553 posts
 
Bi Wire: another urban joke. If you would use a single wire of x guage, instead of a bi-wire that has the same guage (each has half) the single would do better.
It can be analyzed on "Spice" as well explained in simple words. 
Bi wire was a trend of the 90's. No more.
goethe58 OP
16 posts
 
Thanks to all for your insights...appreciate the community spirit.  

As an quick exercise, I checked out Kimber Kable 8TC single run with 8TC jumpers v. 8TC bi-wire.  An 8 ft run of the single 8TC was $493 (pair) and the jumpers $160 for a total of $653.  The 8TC bi-wire was $558.  Go figure.
twoleftears's avatar
twoleftears
5,313 posts
 
Some makes/models just use the same number of wires/strands inside the cable, and wire them differently.  So with those, on the bi-wire model, half the number of strands is being used to transmit treble and half for the bass.  I don't know whether this is the case with the Kimber, but the similarity in price certainly suggests it.
wolf_garcia
6,600 posts
 
I bi-wire my Klipsch Heresy IIIs with AQ Rockets as I was using them for my previous speakers and am too lazy to put my single wire cables back in. I suppose I can stick the jumpers on to replicate the single wire experience, but the sound is currently so good I just don't wanna.
Log in to respond
More to discover
80x80
Audio Art Cable Classic Plus Power
80x80
ANTICABLES Level 2 "Performance Series"
6 Foot Bi-Wire Biwire set
80x80
Silnote Audio Morpheus Reference III
1m Pair Ultra Pure Silver 24K State of The Art Reference