ARC Ref 3 Power Cord


Hi, I was wondering if anyone has replace the stock power cord for the Arc Ref 3 with some other power cord and has found it to improve the preamps performance? I have replaced the power cords on most of my other components and I am thinking of doing the same with the Ref 3. If so, is there anything good out there without spending an arm and a leg on?
tlg
.
The male end of the stock Ref3 power cord will go into an ordinary household wall socket.
.
I know that the female end of the ARC stock cord is 20 amp.
Is the Male end 20 amp or 15 amp? The new cord I want to get is going to go into a Furman power conditioner which in turn goes into my 15 amp wall outlet. I am assuming I want a new cord with a 20 amp female with a 15 amp male end. Can anyone confirm this. Thanks
.
Basic cord.......15 feet. Very, very heavy.....the weight of the cord can pull the connector out of the wall socket...I had to prop-up the cord right underneath the socket to make sure the weight of the cord didn't pull it out of the wall. You might not have that problem with shorter lenghths.
.
Mitch4t
Can you tell me if it was the basic Signal Power Cord or the upgrade silver one they have? How long is the stock cord? Thanks
.
I needed a longer cord than the stock cord and I purchased a Signal Cable Magic power cord.....sounded very good.
.
I am very interested as to how you know that ARC gear is voiced using Shunyata Anaconda Helix Alpha power cords. Can you elaborate please.

Stephen,

I toured ARC factory back in 2007 and have talked to ppl. Both of their systems - the one in the big room with Wilson Maxx speakers, and the one in a smaller room with System 8 speakers, are cabled throughout with Shunyata Anaconda Helix power cords. They also use Shunyata V-Ray.
Give Leonard a call at ARC. He told me that the stock ARC power cords are really good and they also use the snake cords with their equipment in-house. There seemed to be some preferences in which of the none-stock oily cords they preferred with different ARC equipment. Oneobgyn, the SR power cords may be a good fit for your system, give them a try and let us know.
Elberoth2

I am very interested as to how you know that ARC gear is voiced using Shunyata Anaconda Helix Alpha power cords. Can you elaborate please.
ARC gear is voiced using Shunyata Anaconda Helix Alpha power cords. This is what I got when I bought Ref 3. I have tried several other PCs since, but still have the Anacondas.
That Signal cable is below what the REF3 deserves. You have spent the money on a fine pre-amp and need to support it with a good cable. I would likely just stick with the stock cable over buying a cord in that price range.
I looked up the very expensive prices on some of the power cords recommended. I am still wondering if there is someone out there using a Signal Magic power cord on their ARC REF 3. They also offer a Silver Resolution Reference power cord. I wonder what more that one could do compared to their standard power cord. Can someone tell me the length of the stock cord that comes with the REF 3. The back of my system is so cramped that I don't want to trying gettin' back there.
I was thinking of testing the waters with a Signal Power cord. I use that on all my other components and like it a lot. It is also inexpensive also. Is there anyone out there using this brand?
Zargon,

Best of luck in your auditions. One thing I have learned over the past 30+ years in this hobby/addiction---there are NO absolutes---everything affects everything!!
Audioesq,

Your answer is very informative and helpful to understand the environment of your evaluation and what you learned. Thanks for clarifying it.

Like you, I have a dedicated circuit to each component, however, I also have the option of connecting each dedcated circuit either direct to the subpanel or through a 4kva iso to the subpanel. Perhaps I will try some cords and see whether they make a difference in my system and whether they are sensitive to the iso conditioning.
Zargon,
I will attempt to answer your question.
I have eight dedicated 20 amp circuits in my main listening room. These are run from an isolated subpanel. My Ref3 is connected to its own dedicated 20 amp circuit. After running the Ref3 for about 650 hours, I compared the Purist, Stealth, Shunyata and stock power cords. All power cords were previously broken in with about 250 hours of current. Compared with the stock cord, the other cords were significantly better. As for the Purist, it allows the Ref3 to shine, with greater upper and lower frequency extension (about 1/4 octave, according to my sweep tone disc and my Rat Shack sound level meter), much purer tonality, much greater clarity, somewhat greater space between instruments and air, a sweeter yet more detailed presentation, a much darker (quieter) background, and overall more relaxed experience.
I have used these aftermarket power cords both with and without the benefit of dedicated circuits. Aftermarket power cords used without dedicated circuits offer greater overall benefit, but even with dedicated circuits are a significant step up from stock Audio Research power cords.
Your geographic location and power grid anomalies also affect the benefit of aftermarket power cords.
In over 30 years of using ARC amps & pre's, I have always found that changing the stock power cords afforded a significant improvement in the clarity and bass. I started out changing the old hard wired PC's as they deteriorated with visual surface aging of the natural [back then]rubber outer covers.
On the Ref 3 I changed to the Nordost Brahma, after trying the Nordost Valhalla. Brahma made a big difference, Valhalla did not.
However, Valhalla PC's were tried and kept in my phono stage, VPI SDS & SDS to VPI HRX motors, did make a very significant lift in the clarity.
Audioesq, a difference, but what difference?

BTW, do you have dedicated circuits and/or power conditioning? It seems that the systems most influenced by power cords are those without any other power conditioning.
I use the Purist 20th Anniversary Contego Power Cord. I have compared it against the Stealth Dream, the Shunyata Anaconda Alpha Helix and the stock AR cord. My amps are the Lamm Ref 1.2 monoblocks. In my system, the Purist is a slight flavor improvement against the Stealth and Shunyata, and a significant across-the-board improvement against the stock cord. If you are using a Ref 3, you owe it to yourself to audition as many PC's as possible. These PC's are not cheap, but do make a difference. Just my opinion.
Everyone here is using a different PC and some are relatively expensive. Why? What difference did these quite different cords make over the stock ARC cord which is quite substantially made? Did you purchase these cords for evaluation specifically with the Ref 3, or were they left over from previous uses? My only complaint about the stock cord is its excessive length in my application.
Hi good day, my recommendation is: 1 Purist 20 Anniversary, or as a cheaper option Purist Aqueous 20 Anniversary.
Good luck
Adrian
I have been using a Shunyata Python Alpha Helix since I first got my REF3. Exceptional results. Pick one up used.
The standard ARC reference power cord is exceptional and it might be to your advantage to simply use this cord throughout your system if at all possible (it is a 20 amp cord). I have compared it to some of the more expensive power cords and it is as good if not better than the cords priced less than a $1000.00.
Purist Audio Design 20th Anniversary Contego PC Power cord and/or Stealth Dream. Both sound great in my system.